1mm

"1mm" search results in the Electronics Forums



280 results found for "1mm" in the Electronics Forums

Order by: Relevancy |   Date

Step-up stencil: recommendation thickness

Aug 20, 2019 | 6 mil (0.15mm) for the 1.13mm pitch BGA, and 4 mil (0.1mm) for the smal QFN with 0.4mm pitch.

SMT line alignment

Jan 9, 2019 |

Stencil and paste used for .4mm pitch csp component ball size .3mm?

Aug 29, 2018 | It is recommended that the thickness of the stencil of 0.1mm, the steel mesh should be partially nan

Solder Paste Volume measure in SPI

Mar 26, 2018 | I realize that I wrote wrong. Sry The stencil of 0,1mm of thickness is printing 45% more volume.

Solder Paste Volume measure in SPI

Mar 25, 2018 | Hi experts, Is it normal that a stencil of 0,1mm would produce 45% solder paste volume being prin

Fiducials

Jan 31, 2018 | I like a 1mm circle with a 2-3mm mask relief around it.

PCB FINISH FOR HIGH PIN COUNT SAC ALLOY BGA

Jun 3, 2016 | I am planning to attach 1760 pin BGA. The pitch is 1mm and Balls are SAC alloy type. The PCB is for

Fuji cp6 placement issues

Jun 10, 2015 | The published Fuji CP6 placing accuracy specification is plus/minus .1mm I would say that your m

Dek printing issue

Oct 31, 2014 |

Destacker will not separate 1mm thick boards

Oct 21, 2014 | My UIC destacker does fine with 2mm thick boards. However, I have to hand feed the 1mm thick boards

Mydata TM8FC Feeder strange issue

Jan 29, 2014 | Hi i have strange issue on one of my TM8FC feeder feeder seem to have 0.5 to 1mm longer that

Required magnifier for inspection of 0603 component

Sep 30, 2013 | Hi, Ernie, According to IPC610, for land widths > 1 mm, recommended inspection range is from 1.5X

QFN PCB Pad no Drain Hole

May 17, 2013 |

Juki Laser Alignment

May 14, 2013 | Cheers again. So if the bga is 1mm thick and with the balls 1.3 mm thick I should set the component

IR Rework Machine

Jun 28, 2012 |

Fiducial Recognition

Jun 15, 2012 |

Fiducial Recognition

Jun 15, 2012 | ENIAC, 0.040" equates to 1mm, not 0.1mm. 0.040" is the IPC minimum recommended fiducial size and whe

Fiducial Recognition

Jun 15, 2012 | DeanM, if I understood correct, you use fiducial with dimension 0.1 mm and increased it to 0.15 mm.

Wave Solder question

May 23, 2012 | Try trimming the leads to no more than 0.020" instead of 0.040" (1mm). The extra labor on the front

Wave Solder question

May 22, 2012 | Protrusion is 1 mm.

Fiducial Recognition

Sep 2, 2010 |

Fiducial Recognition

Sep 2, 2010 | Hi Resse, there seems to be some mistake in translating aa to mil. I thought, 1mm should have been a

Fiducial Recognition

Sep 1, 2010 |

CP642 Ballscrew Replacement

Jun 25, 2009 | Banging and knocking is not good. The noise that we hear on ours is more of a whining. .1mm runo

Fuji cp43 pcb layout

Nov 3, 2008 |

Tall SMT Components

Jun 18, 2008 |

Fuji CP43 placement

May 19, 2008 | all, The placement was off on one panel ( 4 up ) out of the batch. It was off by approx 1mm in th

QFP100 solderability

Apr 15, 2008 | Hello, We are having a problem with soldering QFP100 (16mmx16mmx1mm). Board dimensions: 70mm

BGA Voids

Feb 11, 2008 |

0201 Capacitor reject rate on Fuji CP643

Oct 10, 2007 | Hello Sr.Tech, There have been two types of nozzles made by Fuji for 0201's one was a 1mm tapered t

132 QFN footprint

Sep 3, 2007 |

BGA Aperture

Jun 23, 2007 | Hi, We use 1:1 for 1 mm BGA and it works fine. We used it at 4 thou laser cut stencils when w

CP6 placement problems

Apr 27, 2007 | Rob, .06mm to .1 mm is slicing the bologna pretty thin. Grab ahold of your placement shafts and

Selective Soldering

Sep 12, 2006 |

Pages: 1 2 3 4 5 6

Reflow Oven

Small Parts Tips