Electronics Forum: 2

Wave and Press-Fit fixtures

Electronics Forum | Mon Dec 03 20:12:41 EST 2001 | Kelvin Kok

Hi Peterson, We are in the business of manufacturing wave, SMT pallets and all kinds of toolings. With our 11 years expertise, we definitely able to meet your requirements with quality products. With our location in Silicon valley and supporting ma

QFN's and LGA's

Electronics Forum | Wed May 20 17:56:51 EDT 2009 | dyoungquist

I have attached a pdf showing the dimensions for the QFN we placed. First, The pins on the part are not only on the bottom side but also wrap around to come up each of the 4 sides of the part as shown in the side view in the attached pdf. This i

PCB Thickness and BLR

Electronics Forum | Mon Jun 03 13:26:32 EDT 2019 | az2019

Hi, I have a general question about the relationship of PCB thickness and BLR testing result. For example, I have QFN6x6 parts mounted on board in 1.2mm, 1.6mm, and 2.4mm thickness. All boards have 6 layers of Cu. Studies show thicker board gives les

Bow and twist of PCB's

Electronics Forum | Mon Apr 23 14:03:18 EDT 2001 | Ryan Jennens

Dougie- We,too, have the IPC-A-600F, and the spec. refers to IPC-TM-650 test method in the back of the book. Look on page Number 2.4.22 of the test methods appendix. This outlines the procedure for determining the percentage of bow and twist,

ICT and specifying PCBA testing

Electronics Forum | Tue Mar 23 07:35:42 EDT 2010 | jooh

Since I'm new to the forum I probably ask previously answered questions (that I have not found) but I would be grateful if someone could clarify this for me. I'm in R&D at a company where we design low volume (1k-10k) fairly complex PCBAs for our pr

force between the pad and laminate material

Electronics Forum | Wed Jun 12 08:13:29 EDT 2002 | davef

Don't sound proper. There is no specification. Pad peel strength test methods are: * IPC-TM-650, Method 2.4.21 for multiple solderings * IPC-TM-650, Method 2.4.8 for copper peel with a Instron machine. Typical requirement for Cu is: 6 lbf/in [1

Re: Shear strength and Copper/Tin Intermetalic layer

Electronics Forum | Thu Jul 09 21:04:50 EDT 1998 | Dave F

| Hi there, | I am looking for some informations concerning the shear or pull strength of a typical TQFP 20 mils leads in relationship with the Copper/Tin intermetalic layer thickness. Could anyone help? | | Thank in advandce. | rgs, | chiakl Chiakl

Foam fluxer maintenance, storage and cleaning

Electronics Forum | Mon Nov 09 09:44:22 EST 2015 | davef

Purpose. This describes setting-up a wave soldering system set-up for a new assembly design or checking a wave solder machine operation with a test board. Applicability. To be used for new design printed circuit assembles and during machine accept

Foam fluxer maintenance, storage and cleaning

Electronics Forum | Sun Nov 08 15:27:25 EST 2015 | davef

Thinner: Flux thinner, NOT paint thinner We kept a spare stone in thinner in inventory. We cut PVC pipe to size, cap in one end, screw thread on the other, stone inside, filled with flux thinner and covered with a screw cap. I don't remember who we

Standard of PCB Bow and Twist in Incoming Inspecion

Electronics Forum | Thu Feb 27 12:27:10 EST 2003 | stevel

Hi all, We got some bare pwb in our incoming inspecion looked really wrapped. The maximum twist of the pwb we messured is 0.056inch by following the method in IPC-TM-650 2.4.22 C. (The diagonal size of our pwb is 7.5inch) According to the IPC standa

  1 2 Next

2,3, and 2,4, searches for Companies, Equipment, Machines, Suppliers & Information