Electronics Forum: 2422 (Page 1 of 2)

I am looking for an IPC spec for intentional PCB warp

Electronics Forum | Mon Dec 22 16:20:03 EST 2014 | warwolf

Basically the contract comes first, then the design drawings then IPC. if your costumer is asking you to bend the PCB then it becomes apart of the design drawings. as for looking for a cover, get it in writing that that's what they want you to do. I

warpage dtandard

Electronics Forum | Sun Aug 24 08:57:56 EDT 2008 | davef

For an nate measurement method, look here http://www.ipc.org/4.0_Knowledge/4.1_Standards/test/2.4.22c.pdf For bare boards, look to IPC-6012, par. 3.4.4 For assemblies, look to IPC-A-610

PCB Warp Issues

Electronics Forum | Fri Jul 16 11:27:57 EDT 2010 | davef

Consider: * Bow & Twist IPC-TM-650; Method 2.4.22 * Previous threads on SMTnet, like: http://www.smtnet.com/Forums/Index.cfm?CFApp=1&Message_ID=54498

PCB Warpage

Electronics Forum | Thu Apr 07 20:16:23 EDT 2005 | davef

Q1) Simple way to measure the PCB warpage A1) IPC-TM-650; Method 2.4.22 Bow & Twist Q2) What is the maximum warpage can the SMT machine allow the to accept and place the component without problem. A2) That depends. IPC-A-610 Acceptability of Elect

Bow and twist of PCB's

Electronics Forum | Mon Apr 23 14:03:18 EDT 2001 | Ryan Jennens

Dougie- We,too, have the IPC-A-600F, and the spec. refers to IPC-TM-650 test method in the back of the book. Look on page Number 2.4.22 of the test methods appendix. This outlines the procedure for determining the percentage of bow and twist,

warpage for 152mm length PCB

Electronics Forum | Thu Aug 09 07:53:16 EDT 2012 | davef

Allowable bow & twist: Together, both IPC-A-600G and IPC-6012B represent the core IPC documents for describing the acceptable and nonconforming conditions that are either externally or internally visible on finished printed boards. IPC-A-600G relies

Standard of PCB Bow and Twist in Incoming Inspecion

Electronics Forum | Thu Feb 27 12:27:10 EST 2003 | stevel

Hi all, We got some bare pwb in our incoming inspecion looked really wrapped. The maximum twist of the pwb we messured is 0.056inch by following the method in IPC-TM-650 2.4.22 C. (The diagonal size of our pwb is 7.5inch) According to the IPC standa

PCB Warpage

Electronics Forum | Sun Apr 10 06:27:50 EDT 2005 | WarpSpeed

1.) First of all: What is Your customers requirements??? 2.) If the customer or You don't have a specification; I will strongly recommend that you follow the "IPC-IPC-TM-650 Method 2.4.22 Bow & Twist" that [DaveF] suggested. 3.) If You have "critic

SMD flatness standard

Electronics Forum | Mon Nov 20 19:49:03 EST 2006 | davef

Sorry for stating this incorrectly. It should been: Bow & twist for bare boards and panels: IPC-A-610 Acceptability of Electronic Assemblies, 10.6: 1.5% for PTH only and 0.75% for SMT, acording to test method TM-650, method 2.4.22 IPC-6012, par. 3.

Need plating on ceramic boards.

Electronics Forum | Tue Aug 31 12:42:45 EDT 1999 | Charles Barker

****************************************** ***************** HELP! *************** ****************************************** We are having a special ceramic smt board made. The boards are 16-up arrays that have smt pads on both sides. Only thre

  1 2 Next

2422 searches for Companies, Equipment, Machines, Suppliers & Information