Electronics Forum: 5

Flash 5.0

Electronics Forum | Mon Feb 04 08:29:43 EST 2002 | jax

Is there something I need to do to keep the Flash 5.0 download menu from popping up on my screen every few minutes? I have a higher version already loaded and do no want to download 5.0, but the constant prompting to do so is annoying.

AOI

Electronics Forum | Wed Oct 17 09:13:50 EDT 2012 | sfeinsp

How to turn OFF message "Solder Insp OFF" on Mirtec 4.5.5.0 program

high speed PCB frequency range

Electronics Forum | Tue Aug 02 06:30:04 EDT 2016 | technotronix

I think it is normally from 4.0 to 5.0

Stencil Design

Electronics Forum | Wed Jun 03 22:07:41 EDT 2009 | davef

= 0.66 aperture opening to the stencil wall has been shown to provide the best transfer efficiency and repeatability of the deposited paste. Values from 0.66 to 0.8 insure a good paste release from the stencil. The biggest impact on area ratio is the

screen thickness

Electronics Forum | Mon Jan 23 22:53:31 EST 2012 | davef

= 0.66 aperture opening to the stencil wall has been shown to provide the best transfer efficiency and repeatability of the deposited paste. Values from 0.66 to 0.8 insure a good paste release from the stencil. The biggest impact on area ratio is the

Soldermask registration capability.

Electronics Forum | Wed May 19 10:35:37 EDT 1999 | Jeffrey L. Gumm

Trying to find a manufacturer with the capability to hold a registration tolerance of +/- .001" in LPISM. To be done on ceramic substrates, with a maximum panel size of 5.0" x 7.0".

Cpk For 0201 Placement

Electronics Forum | Sat Jan 29 23:55:58 EST 2005 | KEN

I recently ran a process evaluation (Print/ P&P /Reflow) and was plesently surprised with a 5.0 sigma process or 250ppm. Attrition was under 1%. Keep in mind this is defects counted Post-reflow. The most signifficant defect was tombstoning / draw-

Uneven solder reflow

Electronics Forum | Wed Jan 17 18:42:49 EST 2007 | Richard

I'm trying to get an even solder coating onto a retangular shaped ceramic substrate (5.0mm x1.83mm), but the solder tends to pool on the short side of the substrate.

DEK HORIZON 265 Squeege Pressure question

Electronics Forum | Wed Nov 06 08:23:53 EST 2019 | dekhead

If it is always showing 5.0Kg as the "target" value on the error on the first print then yes there is a problem. Are you certain that it is accomplishing the requested (12Kg ?) on the prints thereafter? Does it do Heights calibration (no tools requir

CP40 nozzle/bellows

Electronics Forum | Mon Jun 11 16:51:32 EDT 2012 | fredc

If the orings are the same as Quad they are .158 ID and .024 thick. These dimensions are in inches. The thread for the Samsung QSA30 is 5.0 X 0.8mm, this may be the same for the CP40. If this is the correct oring size is it special and relatively ha

  1 2 3 4 5 6 7 8 Next

5,0 searches for Companies, Equipment, Machines, Suppliers & Information

PCB Handling with CE

MSD Dry Cabinets
MSD Dry Cabinets

Outstanding liquid dispensing and UV curing, all within one platform, watch the video.
Sell Your Used SMT & Test Equipment

Software for SMT placement & AOI - Free Download.
Fluid Dispense Pump Integration

Orange Sticks, Wiring Aids & Probes for Soldering & Desoldering.
SMT fluid dispenser

ONLINE IPC Training & Certification