Electronics Forum: 8105 (Page 1 of 2)

Electrovert Bravo 8105 Conveyor belt fluid cleaner

Electronics Forum | Tue Feb 17 13:04:14 EST 2015 | longnguyen

I am looking for the Manual and the Conveyor belt fluid cleaner for the Electrovert Bravo 8105, the conveyor belt fluid container is near the front with the brush point down to belt ( closed to the monitor ), any one know where can i buy this Manual

Electrovert Bravo 8105 Cooling Zone Chiller

Electronics Forum | Thu Nov 18 16:09:12 EST 2004 | ms

Hi Everyone. Are many of you using Bravo 8105 reflow ovens with chiller units? What have your experience been like with them. Are they reliable? If you had the choice would you get another? Is having them an advantage with lead free production?

Electrovert Bravo 8105 Conveyor belt fluid cleaner

Electronics Forum | Wed Mar 02 02:22:09 EST 2016 | akon63

hey dude you can find the manual for the conveyor belt fluid cleaner here http://www.orf.ae/ as a professionals i believe they would be more than happy to help you

Electrovert Bravo 8105 Cooling Zone Chiller

Electronics Forum | Fri Nov 19 10:56:20 EST 2004 | rlackey

Hi Mike, We mainly use chillers for the operators - we build a lot of thick & palletised boards that retain the heat. Having a chiller means we can pick the board up earlier after the oven & it's cooler. With leadfree you will have higher temperat

SMT LED placement with Universal HSP 4791

Electronics Forum | Tue Jan 11 17:19:15 EST 2005 | vickt

Clark, Which component type are you using? Deform? also, is this a domed led? and if so, are you using a nozzle with an approriate ID to seal on the body? Not every LED may be able to be placed with a 4791. Todd

SMT LED placement with Universal HSP 4791

Electronics Forum | Tue Jan 18 11:47:10 EST 2005 | clarkk

JB, I've toggled between front and back lighting and the results are about the same. But thanks anyway for the suggestion. Clarkk

Password for Electrovert Bravo

Electronics Forum | Thu Mar 01 14:35:52 EST 2012 | edmneb

We recently got a used Electrovert Bravo 8105 in house, but the unit did not come with any passwords to access the software. Any one know a default password, or way to change the passwords? Thanks!

SMT LED placement with Universal HSP 4791

Electronics Forum | Thu Jan 13 17:45:24 EST 2005 | vickt

Clark, As a start....Do you have a qualified tech on site to verify that the camera lighting is within spec? If not it's hard to say where you are starting from. I know that UIC still has trained personel that can help you out on this older gear if y

SMT LED placement with Universal HSP 4791

Electronics Forum | Tue Jan 18 11:11:02 EST 2005 | JB

I don't think the light levels can be adjusted manually. Two options that I know of, back ltg and front ltg. If you have auto teach mode, switch between this two. If the bottom is clear use back ltg on a square mold. Hope it helps.

Re: Flux sprayer set up

Electronics Forum | Tue Dec 21 13:27:47 EST 1999 | Vince Whipple

Charlie: As far as setting up a spray fluxer.. Are you spraying no-clean, voc free, water soluble? What you would want to do is to run a blank pcb through the fluxer and pop it out before the preheaters. Visually inspect for variations in uniformit

  1 2 Next

8105 searches for Companies, Equipment, Machines, Suppliers & Information



Software for SMT placement & AOI - Free Download.
pcb assembly supplies

Orange Sticks, Wiring Aids & Probes for Soldering & Desoldering.
High Throughput Reflow Oven

High Throughput Reflow Oven
Electronics Equipment Consignment

High Speed Precision In-Line SPI System - Mirtec MS-11