Electronics Forum: 9.2 (Page 1 of 9)

Mydata TP9-2 and TP11-UFP difference

Electronics Forum | Tue Jul 16 03:58:40 EDT 2019 | artem

Hello, what is the difference between the TP9-2 and the TP11-UFP? The TP11-UFP is larger, can it do something more than the TP9-2 except placing more components?

Mydata (TP9-2U) problem

Electronics Forum | Tue May 07 12:30:30 EDT 2013 | shankar2013

We are having a problem with our Mydata TP9-2U where the machine shuts down during a job with this message seen on the service monitor -- F-MOT1-26/156:MOVFI: MOTOR TIMEOUT Has anybody seen this problem?

Mydata TP9-2U error ?

Electronics Forum | Wed Aug 21 06:19:17 EDT 2019 | mxtimra

Mydata TP9-2U gives error code MOT1-38/186:MSETDYNX What is that code ? Machine give that code and wont make start up process. Appreciate if someone has knowledge that code, thanks.

Mydata TP9 2 Help

Electronics Forum | Fri Mar 20 18:04:59 EDT 2009 | clearblue

We are having the same error message (F-Axis-23: X-Axis transducer ch.1 PTP value too low) on our TP9-2U that you had in 2007 with your TP9 2. I am hoping your memory is excellent, you are still at this email address, and you were able to fix the ma

Mydata TP9-2 Help

Electronics Forum | Tue Aug 07 08:53:03 EDT 2007 | mleber

Thanks for the reply. We are just beginning to troubleshoot the machine. Thanks again.

Mydata (TP9-2U) problem

Electronics Forum | Tue May 07 14:54:38 EDT 2013 | shankar2013

Tried High and highest. Same message on shut down

Need help on Mydata TP9-2U

Electronics Forum | Mon Nov 14 12:11:20 EST 2005 | binhanhaokiet

We just bought a used TP9-2U, I could not do a W-wagon camera calibrate. It keep saying "Calibrate failed, can't located all point", I do not know what should I do next. I did refocus the camera but it still does not help. Please help

Mydata A12 tool tip damage

Electronics Forum | Wed Jul 18 06:47:38 EDT 2007 | cyber_wolf

I was asking if it was a TP9 2U...... If you have a UFP machine then you are in luck. It is most likely the small X-motor. You can test it in the service program. Does the X-axis bounce when you are trimming magazines and stepping through placement

Upside down placement of a crystal oscillator is acceptable ?? As per IPC 8.3.2.9.2 clause its define Rectangular or Square En

Electronics Forum | Tue Jul 19 03:06:42 EDT 2016 | ishwarsingh1

Upside down placement of a crystal oscillator is acceptable or not ?? As per IPC 8.3.2.9.2 Rectangular or Square End Chip Components – 1, 3 or 5 Side Terminations.I am not sure whether is applicable for crystal oscillator or not . Your answer wo

TP9-2U Initializing Problem

Electronics Forum | Wed Aug 05 18:06:34 EDT 2020 | smittym

So I have a old TpSys system running on a TP9-2U and I can't get the initializing hardware when I boot the unit. Once the program loads the computer freezes if I select any of the drop menu items. I can however get it to initialize if I go into Servi

  1 2 3 4 5 6 7 8 9 Next

9.2 searches for Companies, Equipment, Machines, Suppliers & Information

PCB Handling with CE

Smt Feeder repair service centers in Europe, North, South America
fluid dispenser

High Precision Fluid Dispensers
Sell Your Used SMT & Test Equipment

Wave Soldering 101 Training Course
SMT feeders

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
PCB Depanelizers

Training online, at your facility, or at one of our worldwide training centers"