Electronics Forum: add part between two leads of other part (Page 1 of 2)

Re: Use of solder paste for leaded thru-hole parts?????

Electronics Forum | Tue Jul 07 12:52:02 EDT 1998 | Upinder Singh

Thanks Earl. Well following is the data regarding the product. 1. The panel consists of 21 boards. 2. The surface I mentioned would have 3 SMds and 1 T/hole connector. 3. PCB thickness is 55 mils and the width of the hole on the PCB for the thru-

Re: Use of solder paste for leaded thru hole parts????

Electronics Forum | Mon Jul 06 13:17:50 EDT 1998 | Upinder Singh

Hi all . Thanks to Ryan, Brian , Justin and Dave for the timely help earlier. I would appreciate if somebody could help me in the stated issue: I am trying to to place one thru hole 20 pin connector along with the SMT components by p

Re: Substitute parts

Electronics Forum | Tue Aug 31 19:44:25 EDT 1999 | dean

Do any SMTneters out there have a good solution to substitute SMT parts that you are willing to share? I presume all of us have the issue where purchasing wants to buy "the same part" from a different vendor. While the part may be the same electric

Re: Substitute parts

Electronics Forum | Thu Sep 02 17:01:30 EDT 1999 | Brian

Do any SMTneters out there have a good solution to substitute SMT parts that you are willing to share? I presume all of us have the issue where purchasing wants to buy "the same part" from a different vendor. While the part may be the same electr

Re: Wave Solder Problems - VIA HOLES

Electronics Forum | Fri Jun 04 10:02:06 EDT 1999 | Chrys Shea

I'm encountering a new problem at my new company that I haven't encountered before in my past life - and that's Wave Soldering VIA holes. We've been getting a rash of defects that we call in this company, "insufficient solder in VIA hole

Re: Wave Solder Problems - VIA HOLES

Electronics Forum | Fri Jun 04 17:10:59 EDT 1999 | C.K.

I'm encountering a new problem at my new company that I haven't encountered before in my past life - and that's Wave Soldering VIA holes. We've been getting a rash of defects that we call in this company, "insufficient solder in VI

Re: Wave Solder Problems - VIA HOLES

Electronics Forum | Tue Jun 08 11:40:03 EDT 1999 | Steve Skinner

I'm encountering a new problem at my new company that I haven't encountered before in my past life - and that's Wave Soldering VIA holes. We've been getting a rash of defects that we call in this company, "insufficient solder in VI

Re: Thanks.

Electronics Forum | Mon Jun 07 11:10:56 EDT 1999 | Brian Wycoff

Geez, those test guys are always whining about via holes, aren't they? I even had one test guy go over to our finals/add-on department and instruct everone to look for unfilled vias and fill them by hand! Without consulting the area

Re: Thanks.

Electronics Forum | Fri Jun 04 17:26:11 EDT 1999 | C.K.

Geez, those test guys are always whining about via holes, aren't they? I even had one test guy go over to our finals/add-on department and instruct everone to look for unfilled vias and fill them by hand! Without consulting the area manage

Re: BGA Repair Problems

Electronics Forum | Mon Aug 17 02:50:44 EDT 1998 | Bob Willis

Have an SRT w/preheat, 18 layer board all copper, 456 BGA needs to be removed and replaced. The manufacturer is Chip Express and during reflow it warps up or down. Causing either opens or shorts on the corners. I was using gel flux with multiple

  1 2 Next

add part between two leads of other part searches for Companies, Equipment, Machines, Suppliers & Information

Best SMT Reflow Oven

High Resolution Fast Speed Industrial Cameras.
Void free Reflow Soldering

ONLINE IPC Training & Certification


Orange Sticks, Wiring Aids & Probes for Soldering & Desoldering.