Electronics Forum: air cooling (Page 1 of 14)

cooling electronics

Electronics Forum | Tue Oct 13 10:18:18 EDT 1998 | amir faris

Dear leaders of SMTnet i am amechanical engineer work at BHIT (Benha higher institute of technology )in Benha , egypt. I have a new search in electronics .It is Cooling of elctronic equipments using jet of air but realy i donot know a lot about the f

Re: air nozzle

Electronics Forum | Tue Dec 08 15:48:11 EST 1998 | John

| I HAVE SEEN ADVERTISED AN AIR NOZZEL THAT USES COMPESSED | AIR TO SPEW OUT EITHER HOT OR COLD AIR. I HAVE NEED OF | SUCH A DEVICE. I DO NOT HAVE THE MANFR. OF THESE. | ANY SUGGESTIONS ?? | Try Exair corporation. 1-800-exair is the phone #. I thin

Compressor air line material

Electronics Forum | Tue Jun 26 08:42:34 EDT 2007 | grantp

Hi, It's much better to add the cooler after the tank, as the tank will condense a lot of the water before it even hits the cooler and goes out. It's a much better system to have the tank between the compressor and then the cooler. The air also get

Really need Omniflow 7 replacement cooling zone blower motor!!

Electronics Forum | Wed Jan 17 21:02:48 EST 2007 | Jnet

If you are just wanting a replacement blower for your air crossflow cooling section. You should be able to purchase through Electrovert cheaper than $1600 dollars. Someone must have quoted you more than just a replacement blower.

DEK 265 GSX air conditioner refrigerant pressure

Electronics Forum | Sat Mar 30 13:33:50 EDT 2019 | stephendo

This is not an HVAC unit. This is a small unit attached to a production machine to keep the solder paste from drying out prematurely or slumping. The volume of air being cooled and desicated would be less than 3 or 4 cubic meters.

OMNIFLOW 10

Electronics Forum | Thu Sep 18 11:07:39 EDT 2003 | donbell

SR. Tech: I have worked with Omniflo 7 and 10 ovens for many years. I purchased several 10 zone ovens in '98 when I worked for Ericsson. Here are some of my experinces with Electrovert Omniflo ovens; Yes, you can expect to run the conveyor speed a

Lead free rework of BGA

Electronics Forum | Thu Jan 18 08:31:09 EST 2007 | Jeff

Thanks. I will turn off the machine activated cooling and have the part cool down at room temp (no compressed air cooling). Can you recommend a good paste / tacky flux?

BTU VIP98

Electronics Forum | Mon Nov 10 07:22:42 EST 2008 | janz

Hello, I am looking for operation& service manual for reflow oven BTU VIP98 with air cooling and nitrogen. Thank you for any help. janz

Electrovert Bravo 8105 Cooling Zone Chiller

Electronics Forum | Thu Nov 18 16:09:12 EST 2004 | ms

Hi Everyone. Are many of you using Bravo 8105 reflow ovens with chiller units? What have your experience been like with them. Are they reliable? If you had the choice would you get another? Is having them an advantage with lead free production?

Reflow Profiling - Cooling Rate?

Electronics Forum | Mon Feb 10 10:41:29 EST 2020 | SMTA-Tony

Hello Phil, As the other respondents have mentioned, the cooling rate is not easily controlled and varies based on the oven and board design, as well as the settings of the last few zones and cooling zones. In general, the board is going to cool in

  1 2 3 4 5 6 7 8 9 10 Next

air cooling searches for Companies, Equipment, Machines, Suppliers & Information

Global manufacturing solutions provider

World Source Equipment: Used equipment sale. Hundreds of items on sale.
Blackfox IPC Training & Certification

High Precision Fluid Dispensers
SMT feeders

ONLINE IPC Training & Certification
Online IPC Training & Certification

MSD Dry Cabinets
SMT spare parts

SMT & PCB Equipment - MPM, DEK, Heller, Europlacer and more...