alignment

"alignment" search results in the Electronics Forums



1035 results found for "alignment" in the Electronics Forums

Order by: Relevancy |   Date

DEK265 GSX chase clamp error

Jun 4, 2018 | >> mis-alignment?

DEK265 GSX chase clamp error

May 29, 2018 | screen alignment chase clamp state is ON, it can be turned OFF but when I get out of diagnostics mac

What do I win setting up 3 or more fiducials in printer ?

Mar 27, 2018 | Two Fiducials are sufficient for alignment. A third fiducial is useful to make sure the board isn't

Speedline Accuflex issue

Jul 7, 2016 |

First PCB Printing Process

Apr 28, 2016 | We don't use Mylar for aligning the Printer to the PCB for printing paste because that is relatively

Semi-Auto Stencil Printer Vision Systems; Homebrew

Dec 19, 2015 | Do you just wish to use the setup as a visual aid to alignment. In which case this is not a bad idea

MPM UP2000

Sep 22, 2015 | We had 4 of these machines several years ago. If I remember right the drive that aligns the board t

Manually Adjusting Misplaced SMT Components

May 19, 2015 | Parts will self align using Pb free paste as well. If your parts are not self aligning with Pb free

dek horizon 265

Mar 13, 2015 | how helpful is it to use alignment weighting over fiducial offsets ?

Disposition on Discoloration of Boards post reflow

Dec 30, 2013 | Hi Dave , Thanks and will align accordingly .

Samsung CP45 head camera alignmnet fault

Oct 28, 2013 | It will require an alignment. The tools are usually included in the toolbox, one L shaped magnetic

QUAD 4C Laser problem

Sep 6, 2013 |

QUAD 4C Laser problem

Sep 6, 2013 | Mod code 69 in early firmware versions was laser align part size addition but in later versions is w

SMT Line question

Mar 25, 2013 | I am mainly concerned with physical vibration. Will machine to machine alignment be affected.

QUAD 4C mk2 Z axis

Feb 4, 2013 |

Quad IVc Part rejection issue

Aug 16, 2012 | Sounds to me like a dirty quad-align. If you have cleaned the lens and have the same results then yo

QFN aligment issues

Jul 10, 2012 | until you know if you stencil does align with the pads on the board all the fids in the world will n

QFN aligment issues

Jul 2, 2012 |

QFN aligment issues

Jun 29, 2012 |

Attrition... how to measure it?

Jan 30, 2012 | Now knowing that its a Quad, I'm assuming it has QuadAlign which spins the part it just picked in a

Reflow problem

Sep 14, 2010 | There is problem with the alignment of BGA Balls. Check for any vibration. http://hubpages.com/hub/S

IP2 placing parts shifted after servo fixed?

May 1, 2009 | Swapping a servo amp out does not lead to an alignment issue unless the new amp is way out of adjust

Fuji CP3 Tape Leaf Sensor

Apr 23, 2009 | Do any of you fine people have any suggestions on how to align the Fuji CP3 tape leaf sensor? The l

Quad IVc power up

Apr 15, 2009 | In the early days Quad machines were fitted with an alignment system that was purchased from a compa

Quad IVc power up

Apr 14, 2009 |

Hot Bar Soldering

Jan 7, 2009 |

Hot Bar Soldering

Dec 22, 2008 | Yes I agree with Emil that the Jig/Fixture design is crucial for alignment. The hot-bar machine I w

Dek model questions

Dec 9, 2008 | 256 LT or Lite, low end fully auto machine, lower res alignment camera, not as accurate and repeatab

SMT Connector, Placement Issues

Oct 3, 2008 | On a couple of boards, try remove the pins, let reflow align the connector to the pads

QUAD 4C T axis

Jul 31, 2008 |

ultra low cost pick and place?

May 15, 2008 | Thanks Sarason, Laser alignment of components was actually our first attempt - it certainly offer

Small batch Manufacturing

Dec 18, 2007 |

Pick & place

Apr 1, 2007 | Thanks for the tip. By Z was to high during alignment. Dropped to 10 on a 20 mill part. Thanks.

Pick & place

Mar 28, 2007 |

Skewed components

Mar 6, 2007 | DPAK align on the tab with leaded solders. They don't align much with unleaded solders, but we know

PLCC 44 and QFP 240 tilting problems

Feb 19, 2007 | Are your pads on the board aligned correctly? I've seen this a lot lately. Pads on opposite sides

Solder Paste Inspection

Jan 30, 2007 |

IC short

Jan 19, 2007 | print less paste, and make sure that part is aligned properly after placement. Russ

Fluid Dispensers

Dual Lane Reflow Oven