Electronics Forum: annular ring (Page 1 of 7)

2 questions: via tenting and annular ring terminology.

Electronics Forum | Tue Jul 06 19:38:01 EDT 1999 | John

Q #1) Is it more reliable to have the mask tent over the vias or risk getting vias half filled with solder? These are vias with an .020" hole and .040" or .050" pad. Q #2) When speaking of annular rings, I have always thought of them as minimums. Su

Re: 2 questions: via tenting and annular ring terminology.

Electronics Forum | Wed Jul 07 00:28:59 EDT 1999 | Scott Cook

Q #1) Is it more reliable to have the mask tent over the vias or risk getting vias half filled with solder? These are vias with an .020" hole and .040" or .050" pad. John, It depends......mainly on the via size. Tenting works on smaller vias. Tent

Re: 2 questions: via tenting and annular ring terminology.

Electronics Forum | Wed Jul 07 10:25:13 EDT 1999 | John Thorup

Q #1) Is it more reliable to have the mask tent over the vias or risk getting vias half filled with solder? These are vias with an .020" hole and .040" or .050" pad. John, It depends......mainly on the via size. Tenting works on smaller vi

Re: 2 questions: via tenting and annular ring terminology.

Electronics Forum | Wed Jul 07 09:47:41 EDT 1999 | Peter Brant

Q #1) Is it more reliable to have the mask tent over the vias or risk getting vias half filled with solder? These are vias with an .020" hole and .040" or .050" pad. WIth regards to this question, and scott's follow up, I have used the "epoxy me

Re: 2 questions: via tenting and annular ring terminology.

Electronics Forum | Wed Jul 07 13:41:42 EDT 1999 | Dave F

snip If you go for plugging be sure you have a protrusion spec that you can live with. This often results in little bumps of epoxy that can interfere with component placement. For us, tenting .015 vias usually gets us about 80% coverage from

What is the acceptable annular ring size per IPC for 2mm 2x5 header ??

Electronics Forum | Fri Jun 06 13:03:01 EDT 2014 | asksmt

Hi All, i have footprint 2X5 RA HEADER 2MM spacing in design. I am using about 9 mils of annular ring on top side and about 12 mils of annular ring on bottom side. refer picture attached. we are having solder short issues during wave solder so was

IPC Class 3 Annular Ring and Fine Pitch BGA Challenges

Electronics Forum | Mon Oct 09 06:16:31 EDT 2017 | jamesbarnhart

I think you needed an IPC Class 3 annular ring because for very dense designs, the smaller the annular ring the better, as less space is taken by the pad or via and more space can be dedicated to routing the traces in highly populated areas of the bo

Thanks

Electronics Forum | Fri Jul 09 16:32:35 EDT 1999 | John

Thanks everyone. I appreciate the help. John Q #1) Is it more reliable to have the mask tent over the vias or risk getting vias half filled with solder? These are vias with an .020" hole and .040" or .050" pad. Q #2) When speaking of annular

Would YOU except this PCB ???

Electronics Forum | Thu Aug 14 18:33:38 EDT 2008 | smt_guy

Am I Correct to say that the Via's Annular Rings are broken or incomplete? If they are then that's an automatic Failed. regards

IPC Class 3 Annular Ring and Fine Pitch BGA Challenges

Electronics Forum | Wed Sep 13 03:25:43 EDT 2017 | sbar5781

Any insight appreciated!

  1 2 3 4 5 6 7 Next

annular ring searches for Companies, Equipment, Machines, Suppliers & Information