Electronics Forum: ax5 and nozzle (Page 1 of 13)

Max and Min nozzle settings on CP7

Electronics Forum | Sat Jul 24 04:02:18 EDT 2004 | kent_peterson

Two ways at it.You could just put the same nozzle for both the min and max.Or you could move the feeder into a location that has similar parts using the nozzle you want. With the feeder setup it should be optimized for the least amount of nozzle ch

Max and Min nozzle settings on CP7

Electronics Forum | Sat Jul 24 04:02:21 EDT 2004 | kent_peterson

Two ways at it.You could just put the same nozzle for both the min and max.Or you could move the feeder into a location that has similar parts using the nozzle you want. With the feeder setup it should be optimized for the least amount of nozzle ch

Max and Min nozzle settings on CP7

Electronics Forum | Mon Aug 02 13:06:10 EDT 2004 | jbabson1

If the CP7 is like the CP643, it defaults to the MAX size unless that nozzle is skipped. Then it would switch to the next smaller nozzle on that head.

Max and Min nozzle settings on CP7

Electronics Forum | Tue Jul 20 04:16:02 EDT 2004 | Charles Huang

Wondering if there any CP7/F4G programmers out there that can help me out with this one. I'm assuming the setting for max and min nozzle in the "environment" section of the part data would allow me to use either the specified max OR min nozzle in th

Pick and Place Rivet

Electronics Forum | Wed Aug 13 17:39:27 EDT 2008 | awegener

In light of this new information I've received from everybody's comments, I'd like to get more information about pick and place nozzles. How can I learn more? ... What do the nozzles look like? Are there different shapes? What kind might you r

Pick and Place Nozzles

Electronics Forum | Mon Aug 18 15:03:38 EDT 2008 | awegener

I'd like to get more information about pick and place nozzles. How can I learn more? ... What do the nozzles look like? Are there different shapes? Are custom nozzles sometimes used for custom parts or are the nozzles mostly standardized? What kind

Pick and Place Nozzles

Electronics Forum | Mon Aug 18 22:55:05 EDT 2008 | kpm135

Nozzles are really machine specific. Your best bet, if you're looking for the correct nozzle for a part, would probably be to send a strip of parts and the data sheet to the manufacture of the machine and ask them for their recommendation. Most machi

Pick and place labels

Electronics Forum | Thu Sep 23 11:28:57 EDT 2004 | Frank

We have placed labels using the Hover-Davis label feeders on our Juki machines and we used standard nozzles. Are your labels an odd shape where a standard nozzle won't work?

Pick and place labels

Electronics Forum | Fri Sep 24 12:02:57 EDT 2004 | Frank

Yes, I can see your problem, the nozzle makes only good contact in the center and so the ends don't make good contact. The ends tend to curl up during reflow. There were two suggestions to solve this. 1) Let the operator push down the labels befor

Pick and placement forces

Electronics Forum | Wed Nov 24 06:24:52 EST 2004 | Joe

Hi, I am an Engineering student doing some research on the component/nozzle interface on SMT Pick and Place machines. Could anyone tell me the force at which the nozzle hits the component as it is picked from the feeder or the placement force on a

  1 2 3 4 5 6 7 8 9 10 Next

ax5 and nozzle searches for Companies, Equipment, Machines, Suppliers & Information

Dual Lane Reflow Oven

Component Placement 101 Training Course
MSD Dry Cabinets

Inspection mirrors for electronic rework and repair.
SMT feeders

ONLINE IPC Training & Certification
SMT feeders

Repair tools for all your electronic circuit board repair needs.
PCB Depanelizers

SMT & PCB Equipment - MPM, DEK, Heller, Europlacer and more...