Electronics Forum: axis and timeout (Page 1 of 5)

Mydata My9 X MOT motor timeout

Electronics Forum | Sun Jun 12 01:44:59 EDT 2022 | mikevb

I forgot to mention that I've measured and adjusted the cog play on the x axis and so it is within range, if that applies.

Mydata My9 X MOT motor timeout

Electronics Forum | Tue Jun 14 16:23:22 EDT 2022 | glasscake

Cant put a finger on it being an encoder that was just a single possibility. You can always hook up a scope to the encoder and see if they are working appropriately. I would look through the machine's utilities and see if there is some debug or more

GSM1 zero - timeout waiting for spindle up error

Electronics Forum | Fri Sep 14 19:55:06 EDT 2018 | amartineck

I have a GSM1 that when try to zero it, it stops with the "Timeout waiting for spindle up" message. To get thsi up and running, I have set all my machine settings to default and had to reselect the head from a C4 1 head to the flex head. I initially

CP4 jerks all axis after power up and reset sw...

Electronics Forum | Mon Apr 16 13:31:36 EDT 2012 | jdengler

Have you tried to restart F4G and/or MCS/30 after flushing the CP4 memory? I have occasionally ran into the comm error after a reset start. Leave the machine on and restart F4G or the MCS/30 whichever normally is hooked up. If it still won't commu

CP4 jerks all axis after power up and reset sw...

Electronics Forum | Thu Apr 12 15:21:12 EDT 2012 | jdengler

Have you tried to do a reset start? When Fuji's act weird the first place to start is a reset start, then re-load the Proper Status and Program. Jerry

CP4 jerks all axis after power up and reset sw...

Electronics Forum | Mon Apr 16 10:48:58 EDT 2012 | cyber_wolf

Sounds like a bad or out of adjustment servo amp.....

CP4 jerks all axis after power up and reset sw...

Electronics Forum | Wed Apr 11 17:00:28 EDT 2012 | rodrigo

Hi all, Our cp4 moves rather violently (jerks) all axis when the reset sw is pressed after power up. I've got all sorts of errors after boot up: Servo amp error: D,X,Y, etc Overtravel D,X,Y, etc D clutch error, power off machine We've checked all

CP4 jerks all axis after power up and reset sw...

Electronics Forum | Thu Apr 12 17:49:35 EDT 2012 | rodrigo

I've done the Fuji flush. It does the same thing. We can not load proper again because it does not communicate with either the F4G or MCS/30. I was able to boot into mechanical mode at one point but now I can not do that either. This thing is drivi

CP4 jerks all axis after power up and reset sw...

Electronics Forum | Tue Apr 17 13:07:17 EDT 2012 | rodrigo

Well... after much headache I found a bad relay contact in M1CR1E. The good news is somehow the axis are no longer jerking. The bad news is that it still does not work. When I turn it on now it shows this: emergency stop (in red) waiting for reset

AXI and AOI

Electronics Forum | Mon Jul 08 13:49:10 EDT 2002 | msjohnston

HI, We are looking into expanding our current x-ray inspection from manually inspection one panel per lot to 100% automated inspection for all of our BGA and CSP builds. We have 100% manual inspection at the end of our SMT lines and we are consideri

  1 2 3 4 5 Next

axis and timeout searches for Companies, Equipment, Machines, Suppliers & Information

thru hole soldering and selective soldering needs

Training online, at your facility, or at one of our worldwide training centers"
ISVI High Resolution Fast Speed Industrial Cameras

High Resolution Fast Speed Industrial Cameras.
High Throughput Reflow Oven

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
Pillarhouse USA for Selective Soldering Needs

High Throughput Reflow Oven


"回流焊炉"