Electronics Forum: axis ault position (Page 1 of 13)

Z4-axis The position error exceeded the limit

Electronics Forum | Mon Apr 19 16:07:32 EDT 2021 | sacd

Hello. When I am originating machine Juki KE20060RL Error On Initializing appear Z4-axis. The position error exceeded the limit. I am check and diagnosed that motor Z don't move at all. Attached axis monitor shows the current state of the axis . Coul

QUAD 4C T axis

Electronics Forum | Mon Aug 04 08:02:39 EDT 2008 | leemeyer

Miro, The video has nothing to do with the Quadalign. On a good startup and with no nozzle installed run a "Function 30" and post numbers that you get on the handheld terminal. On a bad startup (nozzle in the down position) press the re button on t

QUAD 4C T axis

Electronics Forum | Thu Jul 31 03:20:29 EDT 2008 | miroyu

Hi everyone I have Quad 4C with following problem. When I run machine "cold start" first power up it will run and initialize but after if I turn it off and back on it will NOT initialize. Z axis will push nozzle down and it will remain i that posit

Contact 3AV-100. PCL-240AK position Error. Machine not hommed

Electronics Forum | Fri Jan 28 15:22:07 EST 2011 | dougt

The PLC240-AK is an IC on the stepper board used to control all the stepper driven axis. I don't remember which axis are driven by stepper motors, possibly the table (x axis). Which axis acts wierd or doesn't move when you home the machine?

Quad 4C MK2, Z axis drift

Electronics Forum | Mon Mar 16 06:12:32 EDT 2015 | bobpan

The first thing to do is to change the z-rod. Sometimes a very old z-rod spring will weaken causing it to reject many parts. If it only rejects parts after a nozzle change....you may need to put some super lube grease on the O-rings on the bottom of

Quad 4C MK2, Z axis drift

Electronics Forum | Fri Mar 13 15:09:20 EDT 2015 | marcelorotofrance

Hello everybody Lately our machine has been working pretty well, but it can’t last too long. Now, during this week’s production cycle, it began to increase the component’s reject rate to alarming levels (obviously the operators reported me when the m

DEK 265 motor com error, axis 1,2,3 fatal error

Electronics Forum | Wed Aug 24 05:23:45 EDT 2016 | bukas

hello, DEK wont start and im getting this error message: motor com error, axis 1,2,3 fatal error, reinitialise machine. this happens about 30 sec after BIOSes are copied to shadow ram. euro sys cards are inserted properly and on segment display is s

Ayuda URgente X axis GSM2 dual beam (4688A) machine error Y1 y Y2

Electronics Forum | Wed Mar 03 14:25:02 EST 2021 | astarotf

Hi Spoiltforchoice Thanks for the comment. With the line encoder readers that the machine brings, we performed a positioning reading check, which showed us the increase or decrease in the path that the heads make, with which we conclude that it is re

GSM PWC, calibration issue? PWC axis hits limit switch when setting board width.

Electronics Forum | Fri Feb 19 11:13:02 EST 2016 | ttheis

I'm setting up a product for the first time on my GSM after I completed debugging some other issues. The previous owners had the PWC axis disabled and the axis motor disconnected, so I re-connected it and enabled it and now it homes and moves. When I

Juki KE-2060R Axis Driver: Z4-axis failed originating.

Electronics Forum | Fri Apr 02 14:21:58 EDT 2021 | sacd

Hello. When I am originating machine Juki KE20060RL Error On Initializing appear 1. E603438 Axis Driver: Z4-axis The position error exceeded the limit. 2. E603431 Axis Driver: Z4-asis status error. 3. E604432 Axis Driver: T4-asis failed motion start

  1 2 3 4 5 6 7 8 9 10 Next

axis ault position searches for Companies, Equipment, Machines, Suppliers & Information