Electronics Forum: axis fault position (Page 1 of 19)

GSM1 occasional fault

Electronics Forum | Tue Jan 26 05:42:56 EST 2010 | dilogic

Our GSM1 with Flex2 heads started to generate occasional error message: "Axis head 1 theta positive lead error during move absolute command" and then stop. After palm-down it runs again for some time. Everything looks fine, so I have no idea where

GSM1 occasional fault

Electronics Forum | Thu Feb 04 02:46:39 EST 2010 | dilogic

OK, here we are: 1. OS is OS&2 2. Sw. is USOS V1.14 3. GSM1 4. 2 Flex2 heads 5. Problem is on the front head 6. No 7. No 8. It just stops in the middle of the placement phase, with the head over PCB area. Usually 2 parts are still held on the nozz

Zevatech Z Axis fault

Electronics Forum | Tue Jun 23 08:08:38 EDT 2009 | ptxems

We have a couple of Zeva/Juki PM570L's. One machine has developed a fault with the z axis motor. It is continually 'buzzing', we have checked and there is 24VAC on it. Although even on the other machine there is AC voltage on the motor. We have sw

Zevatech Z Axis fault

Electronics Forum | Mon Jun 29 19:36:08 EDT 2009 | proy

Are you sure it is the Z axis, and not the rotation, I had one machine which often did something similar, it would buzz loudly, especially if you touched or applied rotation pressure to the gear belt which rotates the head. It never caused any hard s

Zevatech Z Axis fault

Electronics Forum | Wed Jul 01 13:41:25 EDT 2009 | jlawson

Are you sure it is the Z axis, and not the > rotation, I had one machine which often did > something similar, it would buzz loudly, > especially if you touched or applied rotation > pressure to the gear belt which rotates the > head. It never ca

GSM1 occasional fault

Electronics Forum | Wed Feb 03 20:26:49 EST 2010 | mika

Hi, First: 1. What os/system? 2. what s/w version? 3. what type of machine model? 4. What type of head configuration? 5. Do you have this head front or back? 6. Do you have encounter this problem before? 7. Have you recently placed any new "high com

MPM UP100 vision fault

Electronics Forum | Tue Nov 17 21:03:46 EST 2015 | wesleyintelli

Our Speedline MPM UP100 has stopped displaying anything on its monitor where the fiducial positions are usually taught with the camera images. The vga cable is working. Are there any commonly occurring issues with the vga vision board? The rest of th

GSM1 occasional fault

Electronics Forum | Thu Feb 04 04:28:52 EST 2010 | mika

You don't by any chance have a s/w called Motion Control s/w? it's on 1-2 floppy diskettes and it will boot from it also. Normally only the UIC field engineers have/has? this. With this we can actually run each axis & valve or whatever independentl

GSM1 occasional fault

Electronics Forum | Thu Feb 04 03:54:46 EST 2010 | mika

Hi, I know that I been out for this exact error message before (several years ago) and I am just thinking about it. It was something simple... Ok. When You say stops in the middle of placement phase; Do you mean in the first task block, have it alre

Z4-axis The position error exceeded the limit

Electronics Forum | Mon Apr 19 16:07:32 EDT 2021 | sacd

Hello. When I am originating machine Juki KE20060RL Error On Initializing appear Z4-axis. The position error exceeded the limit. I am check and diagnosed that motor Z don't move at all. Attached axis monitor shows the current state of the axis . Coul

  1 2 3 4 5 6 7 8 9 10 Next

axis fault position searches for Companies, Equipment, Machines, Suppliers & Information

PCB Handling with CE

Smt Feeder repair service centers in Europe, North, South America
fluid dispenser

High Precision Fluid Dispensers
Sell Your Used SMT & Test Equipment

High Throughput Reflow Oven
AI Data Center Hardware Manufacturing

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
PCB Depanelizers

Training online, at your facility, or at one of our worldwide training centers"