Electronics Forum: back on (249)

Get back on the wall

Electronics Forum | Wed May 17 17:13:47 EDT 2000 | Michael Parker

The MoonMan has spoken. Everybody get back up on the wall, its been long enough that this has been "off the wall". Wish I had more Rambus chips, just got my SMT process dialed in and ran out of stock. Damn.

Tape not pulling back on components causes machine to stop

Electronics Forum | Thu Mar 14 10:49:44 EDT 2013 | babe7362000

Have others seen a higher rate of machine downtime due to the cover tape on parts not pulling back properly. We have the same problem on the Jukis and Quads. About every 3 minutes the machine stops and the operator has to pull the tape back. And in

Industry News: back on (56)

Virtual Industries Announces Show Special on TWEEZER-VAC for MD&M East

Industry News | 2014-05-27 16:28:21.0

Virtual Industries Inc. today announced that it will exhibit in Booth #2551 at the MD&M East exposition, scheduled to take place June 10-12, 2014 at the Jacob K. Javits Convention Center in New York, NY.

Virtual Industries, Inc.

Virtual Industries Announces Show Special on TWEEZER-VAC during MD&M West

Industry News | 2015-02-09 10:49:49.0

Virtual Industries,today announced that it will exhibit in Booth #1527 at MD&M West, scheduled to take place Feb. 10-12, 2015 at the Anaheim Convention Center in California. The company will offer a free magnifier with the purchase of a TWEEZER-VAC (TV-1000-SP8-BD-MAG1 or TV-1000-SP8-BD-MAG1-220) within 30 days of the show.

Virtual Industries, Inc.

Technical Library: back on (29)

An Alternative Dispense Process for Application of Catalyst Films on MEA's

Technical Library | 2008-10-01 14:02:27.0

This paper proposes an integrated system for film application process than consists of closed loop mass calibration to assure film thickness, a noncontact fast jetting process with high edge definition capable of applying films for highly selective areas and patterns. A system to obtain homogeneity of the solid-fluid mix is described and results are shared.


SMT Stencil Design And Consideration Base on IPC

Technical Library | 2010-03-23 11:50:22.0

This document discuss how to design SMT stencil base on IPC-7525. Introduction: PCBA (Printed Circuit Board Assembly) is a segment of printed circuit board technology. This segment of printed circuit board industry is concentrated in assemble all the pieces of electronic industry to one piece before output them to market. This segment covers: interconnection technology, package design technology, system integration technology, board and system test technology

Association Connecting Electronics Industries (IPC)

Videos: back on (1)

Mx400L in production on a 243 pc board using front and rear gantries simultaneously

Mx400L in production on a 243 pc board using front and rear gantries simultaneously


Mx400L has an IPC 9850 speed of 42,000 CPH. It will accomodate a PCB size up to 26.77" x 18.11", it has 6 module heads on the front gantry, 6 module heads on the rear gantry. minimum lead pitch is 15mil, and it will place parts down to 01005 (0402 me

Apex Factory Automation

Express Newsletter: back on (184)


Back to Top Questions or comments? Contact us      © 1995-99 SMTnet


Back to Top Questions or comments? Contact us      © 1995-99 SMTnet

Partner Websites: back on (15571)

Wafer Peel Back Test

GPD Global | https://www.gpd-global.com/co_website/pdf/pbt/Wafer-Option-PBFT-PBT-3000M.pdf

) on the Wafer Peel Back Option are open/closed according to the width of wafer strip to be tested: 30 mm Valve 20 mm Valve 10 mm Valve Open Closed Open Closed Open Closed 10 mm - 15 mm Strip X X X 20 mm - 25 mm Strip X X X 30 mm Strip X X X PBFT Wafer Peel Back Option Page 2 GPD Global® 07/19/07 3

GPD Global

Curing & Back-end Semiconductor Manufacturing

Heller Industries Inc. | https://hellerindustries.com/curing-back-end-semiconductor/

Component Cracking Intermetallic Growth on PCB Dull solder joints ×   Curing & Back-end Semiconductor Manufacturing Increase productivity, improve quality, reduce costs... with curing

Heller Industries Inc.

back on searches for Companies, Equipment, Machines, Suppliers & Information

Sm t t t t t t t t t t net
  1 2 3 4 5 6 7 8 9 10 Next
Count On Tools, Inc.
Count On Tools, Inc.

COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.

Contract Manufacturer / Manufacturer of Assembly Equipment / Manufacturer of Assembly Material / Pick and Place / Repair / Rework

2481 Hilton Drive
Gainesville, GA USA

Phone: (770) 538-0411