Electronics Forum | Thu Oct 11 22:25:50 EDT 2001 | davef
Bruce I�m with yall. Designers and fabricators say �pins�. You say: * BGA pins are 1mm [0.039�] pitch. * BGA pads are 0.4mm [0.0157�] diameter. * BGA pins are 0.6 mm [0.024�] side-to-side. * Board thickness is ~0.4 mm [0.015�] First, as you can
Electronics Forum | Fri Oct 22 11:53:53 EDT 2004 | C Lampron
Hi Christina, What would you be basing the yields off of? Is it solder defect, component placement, etc....? I have worked for a flex house for quite a few years. You are right. The Polyimide is very dimentionally unstable. (even more so on humid da
Electronics Forum | Mon Jun 08 14:19:30 EDT 1998 | Gary Simbulan
Earl, et al, Boy things get old and cold around here fast. I promised more detail on my capactior problem and I thought I could drop something completely different in the same message and tell a tale of solder balls. First the caps. We still have
Electronics Forum | Wed May 19 14:58:31 EDT 1999 | Wendy Casker
John, Thanks for the advice. I spoke with some of the connector suppliers apps guys today and they have what is called "European" style tooling which consists of top and bottom tooling. The board sits on rails and the Bottom tooling receives the pi
Electronics Forum | Fri May 21 15:51:49 EDT 1999 | JohnW
Wendy.. I found that little nugget a good one from my connector suppliers..Oh we have a tool to put it in for u..only catch was the one I needed was �37K ! ! after falling off my seat I went for something like what I described blow..cost about �1K.
Electronics Forum | Fri Jun 04 14:00:32 EDT 1999 | Arthur Burdick
Wendy, we at ASG make electric presses for press fit connectors, and have made fixtures for AMP Zpak connectors. give me a call i believe we can help. 561-848-6746 Arthur | Wendy.. | | I found that little nugget a good one from my connector supp
Electronics Forum | Mon Nov 27 17:47:23 EST 2000 | Dave F
Gyver: Lemme take a wack [if you�ll excuse the expression, given direction of the later discussion] at your questions. Q1. Will the baking of BGA or PCB cause more oxidation before the SMT process? A1. It certainly will not cause less oxidation,
Electronics Forum | Fri May 14 11:17:42 EDT 2004 | Ashok Dhawan
I am having coating adhesion problem with flex circuits. The cover plate material is KAPTON or Poly imide. The conformal coating material used is humiseal 2A64. The boards are cleaned, measuring less than 4 microgram Nacl per sq in. against acceptabl
Electronics Forum | Mon Jun 08 14:52:16 EDT 1998 | Gary Simbulan
| Earl, et al, | Boy things get old and cold around here fast. I promised more detail on my capactior problem and I thought I could drop something completely different in the same message and tell a tale of solder balls. | First the caps. We stil
Electronics Forum | Tue Jun 16 15:01:58 EDT 1998 | Gary Simbulan
There are some common reason for capacitor cracking on my web page if you want to have a look. The document can be downloaded for your reference. | Earl, et al, | Boy things get old and cold around here fast. I promised more detail on my capactior
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
winsouce.jpg)