Electronics Forum: best and solder and flux and to and use and for and wave (Page 1 of 2)

Wave flux and profiling

Electronics Forum | Mon Dec 18 23:24:50 EST 2006 | grantp

Hi, Yes, I would hate to resort to cleaning, but the product must be clean. We have been using palettes to keep most of the flux off the PCB, but there is still residue around the connectors. Does anyone suggest a good no clean flux to use with le

wave soldering and solder bridge

Electronics Forum | Mon Dec 17 12:06:58 EST 2007 | pjc

5 Steps to Eliminate Bridges: 1. Establish (wave) Parallelism First and foremost, you must establish board-to-wave parallelism. This is the prerequisite to any wave solder process control. For an understanding of the power of this approach go to ht

SMT Solder paste and wave flux evaluation

Electronics Forum | Fri Jan 28 12:18:32 EST 2005 | Chunks

Your best bet is to do a decision making matrix. Each company has so many different criteria�s it's hard to pick out which one might be important to yours. Simply pick out your top 5 paste manufactures. Next decide what your "Eliminators" are - th

Re: Standard pad sizes for reflow and wave

Electronics Forum | Sun Sep 05 03:52:11 EDT 1999 | Brian

We've noticed that there are many different recommendations for pad sizes for various SMT parts. This seems to vary wildly from manufacturer to manufacturer for the same case sizes. Is there any standards that can used used to specify these sizes

No solder and solder bridge after Wave solder machine

Electronics Forum | Thu Nov 17 21:46:48 EST 2005 | C. Kolokoy

With DIP type components, a sub-par fluxing method (foaming a no-clean), and a chip wave where one is not needed are formulas for bridging and insufficient wetting. If you have SMD's on the wave solder side of the board greater than 0603, and no SOT

Re: WAVE SOLDERING and Gluing 0603 packages

Electronics Forum | Sun Apr 25 12:05:50 EDT 1999 | Chrys Shea

Has anyone had trouble waving and gluing 0603 R's and C's? At my company, our designers have "opened the floodgates" on bottom-side 0603's. We've got an EPK+ with rotary chip and omega wave but can't seem to get skip-free solderin

Re: WAVE SOLDERING and Gluing 0603 packages

Electronics Forum | Mon Apr 26 09:18:27 EDT 1999 | C.K.

Has anyone had trouble waving and gluing 0603 R's and C's? At my company, our designers have "opened the floodgates" on bottom-side 0603's. We've got an EPK+ with rotary chip and omega wave but can't seem to get skip-free so

Re: WAVE SOLDERING and Gluing 0603 packages

Electronics Forum | Fri Apr 23 15:33:50 EDT 1999 | C.K.

Has anyone had trouble waving and gluing 0603 R's and C's? At my company, our designers have "opened the floodgates" on bottom-side 0603's. We've got an EPK+ with rotary chip and omega wave but can't seem to get skip-free soldering on t

Re: Fountain Wave Soldering and Repair/Rework Equipment

Electronics Forum | Fri Jan 22 15:48:14 EST 1999 | Chrys

Hello, I will be evaluating and qualifying two equipment types. The first is a fountain soldering device. I need practical advice on all the stuff you guys and gals know about as good, bad, ugly, best applications, setup, limitations, and all

Tape and shunts are good ideas for WS *BUT*...

Electronics Forum | Tue Jul 28 07:02:59 EDT 1998 | smd

Right now we are taping the goldfingers which is effective but also expensive. Also, some tape was leaving yellow marks on the goldfingers. We're trying the so-called goldfinger glove from Steven's Products. It's a very small company (probably one gu

  1 2 Next

best and solder and flux and to and use and for and wave searches for Companies, Equipment, Machines, Suppliers & Information

Flux Connectivity
Flux Connectivity

Flux is your source for custom cable assembly, wire harness, and electrical enclosure manufacturing. We design and manufacture to your specification and can assist with connector selection, layout, and manufacturing techniques.

Contract Manufacturer / Assembly / Soldering / Test Services / Turnkey

4030 8 Street SE
Calgary, AB Canada

Phone: 1-800-557-3589

XTECH AUCTIONS

High Throughput Reflow Oven
Void free Reflow Soldering

ONLINE IPC Training & Certification
Non-heated dispensing system

Outstanding liquid dispensing and UV curing, all within one platform, watch the video.
pcb assembly supplies

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
Accurate and consistent volumetric Dispensing System Solutions for 1- and 2-component fluids with ASYMTEK Vortik family of pumps. Learn more.

PCBA services - from simple board assembly to complex product development and testing