Electronics Forum: bga and re-balling (Page 1 of 44)

6 layer board and routing bga package

Electronics Forum | Fri Feb 19 05:08:40 EST 2016 | truewanderer

Thank you Tsvetan Usunov

6 layer board and routing bga package

Electronics Forum | Tue Feb 16 13:58:02 EST 2016 | tsvetan

this document http://www.latticesemi.com/view_document?document_id=671 may be good start point but note that how to escape from the BGA is not big deal, how to route your filtering capcitors, grounding, impedance control lof you high speed signals ar

6 layer board and routing bga package

Electronics Forum | Fri Feb 19 05:14:04 EST 2016 | truewanderer

Hi, i have a confusion to read the dimension of BGA package from the datasheet. I have attached the datasheet below. Is this diameter of the ball 0.30mm or 0.15mm. I'm confused about the values given in the box. Whats meant by M, S, A and B. Please g

6 layer board and routing bga package

Electronics Forum | Thu Feb 11 07:24:40 EST 2016 | truewanderer

I'm planning to design the pcb of my project. The controller used is having 136 pins and the package is P-LFBGA. So i think i need to design a 6 layer board for better performance. I haven't designed a multi layer board before. So what are things tak

looking for bga rework station

Electronics Forum | Thu Apr 08 16:25:38 EDT 1999 | greg c

I am looking for a BGA rework/placement system and would like any experience that you have had. I am looking for a system that is reasonable for the placment, removing and re-balling thank you

Re: looking for bga rework station

Electronics Forum | Fri Apr 09 12:46:10 EDT 1999 | Bob Barr

I have been using an Air-Vac DRS-22 for almost two years with very good results. Once a profile is developed it is very repeatable. The DRS-22 is no longer available, however. It has been replaced by the DRS-24. Unfortunately, the DRS-24 has a lo

Re: looking for bga rework station

Electronics Forum | Thu Apr 08 21:23:21 EDT 1999 | Dean

| I am looking for a BGA rework/placement system and would like any experience that you have had. I am looking for a system that is reasonable for the placment, removing and re-balling | | thank you | -I have had wonderful results with SRT. Che

Re: looking for bga rework station

Electronics Forum | Tue Apr 13 18:12:54 EDT 1999 | David

| I am looking for a BGA rework/placement system and would like any experience that you have had. I am looking for a system that is reasonable for the placment, removing and re-balling | | thank you | You might want to look at Advanced Techniques

Re: looking for bga rework station

Electronics Forum | Sat Apr 10 10:01:43 EDT 1999 | Jeff Price

| | I am looking for a BGA rework/placement system and would like any experience that you have had. I am looking for a system that is reasonable for the placment, removing and re-balling | | | | thank you | | | -I have had wonderful results with

I want to learn about bga technology from a pick and place mache

Electronics Forum | Thu Jul 15 12:09:10 EDT 2010 | wrongway

if the BGA has leaded balls use leaded paste if the BGA has lead free balls use lead free paste and set your oven profile to match the paste

  1 2 3 4 5 6 7 8 9 10 Next

bga and re-balling searches for Companies, Equipment, Machines, Suppliers & Information

Selective soldering solutions with Jade soldering machine

High Precision Fluid Dispensers
Selective soldering solutions with Jade soldering machine

High Throughput Reflow Oven