Electronics Forum: bga reballing (Page 1 of 27)


Electronics Forum | Mon Jan 12 20:43:39 EST 2004 | Al

who has the step by step how to reball a Ceramic BGA this is a CBGA 50 mil pitch 29 by 29 mm size


Electronics Forum | Mon Jan 12 23:50:08 EST 2004 | Dean

High temp balls (spheres for you PC types) They are non-eutectic balls. Do you have a reballer or stencil setup? If one device...may not be cost effective, but if many you can usually send back the the IC house for re-ball. There are only a handf


Electronics Forum | Thu Jan 22 15:51:08 EST 2004 | solderboffin

CBGA devices are a bit trickier to reball than run of the mil plastic devices. Once assemblied they are a bit like a sandwich when fitted to a PCB. From top to bottom it goes BGA device - Eutectic solder - High temp solder ball - eutectic solder -


Electronics Forum | Tue Jan 13 15:16:12 EST 2004 | drewhmi

A small benchtop system uses a mask, tooled for your part, to arrange the solder spheres onto the BGA, after it has had the excess solder heat-vacuumed off and a new layer of flux applied. The spheres are poured into the cavity, excess decanted off.


Electronics Forum | Tue Jan 13 16:07:07 EST 2004 | angiewest

Have you looked at solderquik? Winslow Automation sells them. I've had good luck with them. They are bga preforms with the balls on a water soluble paper.


Electronics Forum | Tue Jan 13 16:01:06 EST 2004 | russ

I believe that solder paste will need to be applied to this part. I have re-balled these in the past in a low volume situation and here is what I did and there appears to be no adverse effects to the component. Get a stencil (I use 8 mil for .032"

BGA reballing

Electronics Forum | Wed Feb 21 09:52:56 EST 2007 | SMTRework

Hello everyone, I'm wondering if anyone knows of an automatic BGA reballing unit / system? I'm aware of the "martin" / Manncorp" unit but was looking for info on other manufacturers of this type of device. I usually need to reball about 10 pcs at

Bga reballing

Electronics Forum | Thu Jul 22 21:48:21 EDT 1999 | kyung sam park

Does anyone have any experiences with bga reballing. When I had reworked failed bga part with new part It was good. So I tried to reball bga detached but failed . I guess the cause of fail is thermal shock. IS IT OK TO REBALL BGA PARTS DETACHED ?

BGA reballing

Electronics Forum | Wed Feb 21 10:39:06 EST 2007 | russ

Contact practical components, they have masks and balls, I would not call it automated though. These are simply placing the mask over the part and dumping the balls on it then removing (brushing)the excess balls. I have run and reballed BGAs with ou

BGA reballing

Electronics Forum | Wed Feb 21 11:53:42 EST 2007 | SMTRework

Hi Russ, Thanks for the suggestion. I have the practical components sets that you mentioned, they take too long to do 10 pcs, the "pre-forms" are much faster. What equipment do you use for your automated process?

  1 2 3 4 5 6 7 8 9 10 Next

bga reballing searches for Companies, Equipment, Machines, Suppliers & Information

Precision PCB Services, Inc
Precision PCB Services, Inc

Products, services, training, and consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep & Sole Agent in North America for Shuttle Star BGA Rework Stations.

Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider

1750 Mitchell Ave.
Oroville, CA USA

Phone: (888) 406-2830

Selective soldering solutions with Jade soldering machine

Benchtop Fluid Dispenser
Global manufacturing solutions provider

Reflow Soldering 101 Training Course
We have an exciting array of production equipment for sale, including cutting-edge LED, lamp, and halogen manufacturing lines. You'll find state-of-the-art SMD assembly lines, R&D equipment, and a wealth of laboratory test and measurement tools

World's Best Reflow Oven Customizable for Unique Applications
design with ease with Win Source obselete parts and supplies

MIRTEC - the Global Leader in PCB INSPECTION Technology.