Electronics Forum: bga spray fluxing (Page 1 of 101)

spray gun for flux

Electronics Forum | Wed Dec 19 16:05:10 EST 2018 | ldavis

I created a spray fluxer for our wave solder years ago that is still working well although does consume a lot of flux and is also rather messy. It's cheap and easy though so what the heck, right? I just machined a manifold that will hold four BETE

spray gun for flux

Electronics Forum | Tue Dec 18 04:13:27 EST 2018 | bukas

hello everyone, i'm looking for a spray gun that can withstand flux aggression. I made air controlled prototype for ersa wave machine, but air guns wear out quickly and start to leak. I was thinking about Binks model 95AR or something with stainless

Choosing a spray fluxer.

Electronics Forum | Tue Apr 06 17:27:24 EDT 1999 | Kennyv

I am getting ready to purchase a spray fluxing system for a no-clean process. I have narrowed it down to the Nordson or Dover system. Does anyone have any experience with either. If so can you relate with me. I am a little leary of the Nordson be

Spray fluxing VOC free, as operation HOURS before wave solder

Electronics Forum | Wed Sep 20 10:36:27 EDT 2006 | proy

I am considering moving my spray fluxer into a completely separate operation. Has anybody any comments of sraying VOC free flux on boards, then putting them in a drier/holding rack for possibly say overnight, then running them through wave solder?

Spray fluxing VOC free, as operation HOURS before wave solder

Electronics Forum | Wed Sep 20 12:14:08 EDT 2006 | Rob

Good question - as it is a water based flux then you are going to get a very low level of solvent evaporation, and it's hardly going to be absorbing additional water whilst sitting around. (you actually want the water (carrier element) to evaporate).

Spray fluxing VOC free, as operation HOURS before wave solder

Electronics Forum | Thu Sep 21 10:52:43 EDT 2006 | russ

Could you not just switch to alcohol based flux? If your prob is getting the water off the board prior to hitting the wave, maybe you could install some type of convection to aid in this? Russ

Spray fluxing VOC free, as operation HOURS before wave solder

Electronics Forum | Fri Sep 22 04:48:14 EDT 2006 | greg york

Apply the bare minumum amount of VOC free typically 50% less than alcohol fluxes. By doing this you can keep the same top board temperature as alcohol, its only when people over flux do you need to boost up the preheater to volatise of the water. NEV

Spray fluxing VOC free, as operation HOURS before wave solder

Electronics Forum | Wed Sep 20 16:27:06 EDT 2006 | proy

As we are a low volume shop, the extra handling is not too much of a concern. My biggest concern is if the flux sitting on teh board for a long time (few hours) is going to cause any problems in solderability. My thought is that it should not as it

Humiseal 1A33 conformal coating using automated atomized spray

Electronics Forum | Tue Jul 03 01:54:42 EDT 2018 | rdhiman1

Reaching out to all conformal coating experts, please help! While setting up conformal coating using the automated atomized spray, we observing issues associated with conformal coating wetting on the following regions: 1) Component edges 2) Metalli

Re: Choosing a spray fluxer.

Electronics Forum | Thu Apr 08 13:24:36 EDT 1999 | ADRIANO FERNANDES

| | I am getting ready to purchase a spray fluxing system for a no-clean process. I have narrowed it down to the Nordson or Dover system. Does anyone have any experience with either. If so can you relate with me. I am a little leary of the Nordso

  1 2 3 4 5 6 7 8 9 10 Next

bga spray fluxing searches for Companies, Equipment, Machines, Suppliers & Information



Best Reflow Oven
Sell Used SMT & Test Equipment

World's Best Reflow Oven Customizable for Unique Applications
Software for SMT

High Precision Fluid Dispensers