Electronics Forum: bioact (Page 1 of 2)

Cleaning solvent for no-clean board.

Electronics Forum | Fri Jun 07 14:58:03 EDT 2002 | Ron Costa

Petroferm BioAct 105 works well for Indiums SMQ-92J

effective liquor for cleaning the residues in reflow oven

Electronics Forum | Wed Jun 13 17:17:57 EDT 2001 | medernach

I use BioAct SC-10 and it seems to work pretty well. The best bet is to contact your solder paste manufacturer and ask them for a recommended cleaning solvent for the flux residues... Regards, Justin

flux on PCB's after cleaning

Electronics Forum | Wed Jul 21 17:49:52 EDT 2004 | jsk

problem: Too many solvents and boards are not clean Flux remains on the board after vapor degreaser and "Powdery" white residue after vapor degreasing Flux type is kester 186 Process: hand solder High Temp alloy, spot clean after hand solder e

Cleaning stencils after printing SMD adhesives

Electronics Forum | Tue Jul 10 13:45:23 EDT 2001 | markhoch

We're stencil printing a Loctite 3614 Chipbonder adhesive, and we're using BioAct SC-10 presaturated wipes to clean the stencil after printing, without much luck. Operators are not able to remove all adhesive material left in the aperatures, and aft

Cleaning SMD Adhesives

Electronics Forum | Mon Jul 29 15:24:07 EDT 2002 | OhioD

Interesting. From the reaction we got from DEK, I thought we were the only ones with pumpprint woes. We've tried 1 stencil with Bioact SC10, Hydrex SP&WS, Axarel, and Loctite remover on both Heraeus and Loctite glues. Some we spray, some we work-in m

Freshman in SMT industry needing advice

Electronics Forum | Thu Mar 04 15:34:55 EST 2004 | adlsmt

I agree with above but would like to add: 1. You may want to try something like Bioact SC-10 wipes to clean your stencils. If what your using works good stick with it. Ultrasonic cleaners are expensive, take up room and my experience has not been go

Cleaning Indium TACFLUX007

Electronics Forum | Mon Jun 17 17:04:15 EDT 2002 | pjc

Guys, Thanks for the input. Its a Opto-Electronic project I'm working on for a customer with a device on a ceramic substrate. Yes, I did learn from Indium that 007 is no-clean and has a high-solids content. They reccommended using TacFlux 010, which

Freshman in SMT industry needing advice

Electronics Forum | Sat Mar 20 08:37:06 EST 2004 | Primus

The BioAct SC-10 wipes work great, but I've noticed some contamination in our solder joints after I began using them on the stencils. After cleaning the paste off the stencil with the wipes, I started spraying the stencil down with isoproponal and bl

Re: Cleaning No Clean Wave Solder Carriers

Electronics Forum | Fri Jan 08 10:07:26 EST 1999 | Chrys

| I'm in the process of moving from water washable flux to a full no clean process for the wave soldering process, thing's seem to be going well (so far...). | The one problem I still have is cleaning the wave solder carrier's to remove the no clean

Re: Cleaning No Clean Wave Solder Carriers

Electronics Forum | Mon Jan 18 19:53:58 EST 1999 | Rob F

| | I'm in the process of moving from water washable flux to a full no clean process for the wave soldering process, thing's seem to be going well (so far...). | | The one problem I still have is cleaning the wave solder carrier's to remove the no cl

  1 2 Next

bioact searches for Companies, Equipment, Machines, Suppliers & Information