Electronics Forum: board warp (Page 1 of 34)

warp and twist

Electronics Forum | Tue Feb 14 09:10:43 EST 2017 | davef

Assuming the traces run parallel and perpendicular to each other, I'd choose one direction the traces run as "x" and the other direction for "y." Then I'd pick a unique identifier on the board to insure proper orientation. Next, I'd measure warp and

DoE on post-reflow PCB - warp

Electronics Forum | Thu Jun 27 17:24:17 EDT 2002 | Daan Terstegge

Never did a DOE on that, but I think it would be quite difficult to warp a board inside the oven if it was flat when it entered the machine. If there's no center-board support then it's another story, then the board will bend due to it's own weight.

DoE on post-reflow PCB - warp

Electronics Forum | Wed Jun 26 08:53:32 EDT 2002 | davef

We have not done a DOE on board warping. Consider: * How close the board gets to its Tg during the reflow cycle * Amount of copper on each side and the balance between the two * Thickness of the board * Overall length x width * Time at temperature

DoE on post-reflow PCB - warp

Electronics Forum | Wed Jun 26 21:05:15 EDT 2002 | ianchan

Hi Dave F, customer calls it "warp", we can call it "twist/bow"..etc. the "warp" occurs on individual PCB cells of 28per each panel. the overall dimension of the panel is 139mm x 168mm, and each individual PCB cell is 2.4mm x 1.2mm. Thickness is 0.

smt on flexible board

Electronics Forum | Sun Dec 19 10:02:55 EST 1999 | ron chua

Hi, how to ensure flexible boards do not warp after reflow and still remain flat for subsequent operations. What is the best way to hold and transport these strips from one process to another. Thanks!

Large board BGA rwk

Electronics Forum | Mon Jan 09 19:09:45 EST 2006 | Mike

Basically the same exact way as a much smaller board. The only difference is the profile. Most of our boards are 0.063" thick. Looks like you found your problem. If the edges of the board are cold relative to the rework site (high difference in t

Large board BGA rwk

Electronics Forum | Mon Jan 09 17:35:32 EST 2006 | russ

How are people getting BGAs reworked on boards that are 15"x15" at .06" thick? The BGAs are pretty much in the center of these assemblies. We have just received these and I cannot keep from warping/bowing as much as 1/2" at the heated area. Our bot

Re: bare board problem

Electronics Forum | Fri Jun 18 10:46:10 EDT 1999 | Scott Cook

| | | first of all what is the technical term for the small amount of solder on a plated pad. we are getting poor screen printing gasketing on a 20 mil qfp due to this solder not being even or too high in spots and not covering the length of the pads

Re: bare board problem

Electronics Forum | Fri Jun 18 11:37:10 EDT 1999 | Earl Moon

| | | | first of all what is the technical term for the small amount of solder on a plated pad. we are getting poor screen printing gasketing on a 20 mil qfp due to this solder not being even or too high in spots and not covering the length of the pa

pcb board deflection when mounting component

Electronics Forum | Wed Oct 30 01:23:19 EST 2002 | jasper

Normally warp max 1% of diagonal board measurement is acceptable. What's your p&p like? Some will not experience problems at all! reg Jasper

  1 2 3 4 5 6 7 8 9 10 Next

board warp searches for Companies, Equipment, Machines, Suppliers & Information

Sell Used SMT & Test Equipment

High Precision Fluid Dispensers
SMT feeders

Wave Soldering 101 Training Course
Circuit Board, PCB Assembly & electronics manufacturing service provider

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
Gordon Brothers October 2-30, 2024 Auction

World's Best Reflow Oven Customizable for Unique Applications