Electronics Forum: bonding high temperature (Page 1 of 85)

high temperature solder alloy

Electronics Forum | Thu Oct 07 14:40:31 EDT 1999 | Carol Zhang

I have a board, 4 spacers needed to be soldered on the board first with the normal 62Sn37Pb alloy. Then, capacitors are manually soldered on the boards. The density of the board is quite high. If we wave soldered capacitors first, there will be no p

Omniflo 5 high temperature warning

Electronics Forum | Thu Sep 04 02:43:09 EDT 2008 | benefon

Thanks This error only occurred with one oven profile with the reflow zone temperature set at 270�C. Perhaps it really has to do with the exhaust pull as the oven is operating very near its temperature limit with this profile. I will check that. Tha

Re: high temperature solder alloy

Electronics Forum | Thu Oct 07 15:39:59 EDT 1999 | Carol Zhang

| I have a board, 4 spacers needed to be soldered on the board | first with the normal 62Sn37Pb alloy. Then, capacitors are manually soldered on the boards. The density of the board is quite high. If we wave soldered capacitors first, there will b

Omniflo 5 high temperature warning

Electronics Forum | Tue Sep 02 13:35:29 EDT 2008 | evtimov

Hi, I don;t thing there is an overtemperrature sensor. Just the thermocpouple returns a higher temp(voltage) to the controller and your software goes to alarm, cooldown or what ever it does. Emil

Re: high temperature solder alloy

Electronics Forum | Fri Oct 08 16:48:57 EDT 1999 | Dave F

| I have a board, 4 spacers needed to be soldered on the board | first with the normal 62Sn37Pb alloy. Then, capacitors are manually soldered on the boards. The density of the board is quite high. If we wave soldered capacitors first, there will b

Re: high temperature solder alloy

Electronics Forum | Tue Oct 12 08:48:16 EDT 1999 | Carol Zhang

| | I have a board, 4 spacers needed to be soldered on the board | | first with the normal 62Sn37Pb alloy. Then, capacitors are manually soldered on the boards. The density of the board is quite high. If we wave soldered capacitors first, there wi

Omniflo 5 high temperature warning

Electronics Forum | Wed Sep 03 07:39:19 EDT 2008 | pjc

You may not be getting enough exhaust pull, so the cooling modules over temp. Try swapping blower motors to isolate that before buying one. STANDARD AIR OPERATION: - Load-end: 150 cfm (255 m3/hr) at the 4� (102 mm) stack (minimum requirement) - Unlo

Re: high temperature solder alloy

Electronics Forum | Fri Oct 08 08:26:03 EDT 1999 | Carol Zhang

| | | I have a board, 4 spacers needed to be soldered on the board | | | first with the normal 62Sn37Pb alloy. Then, capacitors are manually soldered on the boards. The density of the board is quite high. If we wave soldered capacitors first, ther

Re: high temperature solder alloy

Electronics Forum | Fri Oct 08 10:08:48 EDT 1999 | Glenn Robertson

| | | | I have a board, 4 spacers needed to be soldered on the board | | | | first with the normal 62Sn37Pb alloy. Then, capacitors are manually soldered on the boards. The density of the board is quite high. If we wave soldered capacitors first,

Re: high temperature solder alloy

Electronics Forum | Thu Oct 07 16:57:02 EDT 1999 | Glenn Robertson

| | I have a board, 4 spacers needed to be soldered on the board | | first with the normal 62Sn37Pb alloy. Then, capacitors are manually soldered on the boards. The density of the board is quite high. If we wave soldered capacitors first, there wi

  1 2 3 4 5 6 7 8 9 10 Next

bonding high temperature searches for Companies, Equipment, Machines, Suppliers & Information