Electronics Forum: bridging (Page 1 of 104)

0402 bridging

Electronics Forum | Tue Jun 02 15:01:57 EDT 2015 | tombstonesmt

What is the reduction in aperture size for your stencil versus pad? Or are they at 100%?

0402 bridging

Electronics Forum | Tue Jun 02 16:16:35 EDT 2015 | ldempsey

Well, I'm speaking in general Our stencil guy insists on those part edits at 100% He's one of the loudest voices calling for me to "Stop slamming the parts into the PCB" All my research so far says we need to be looking at the stencil apertures.

0402 bridging

Electronics Forum | Tue Jun 02 17:32:53 EDT 2015 | jldowsey

Les, Some of the answers to design or stencil aperture/placement machine depend upon what is the current spacing between your components which you didn't specify. Chip components such as 0402's and 0201's typically have very small reductions in pas

0402 bridging

Electronics Forum | Wed Jun 03 15:45:36 EDT 2015 | ldempsey

Well, it took me a while but I had a look at some gerbers. On a PCB with neighboring 0402's 0.006" apart, and paste reduced 0.75mil on each side, I get lots of bridging. On a later rev of the same PCB, we have neighboring 0402's 0.018" apart,and pa

0402 bridging

Electronics Forum | Tue Jun 02 13:42:44 EDT 2015 | ldempsey

Hello all, Some background. We have JUKI machines (FX2, KE2000's and KE3000's) We're looking into an issue with 0402's in close proximity to each other. The paste gets mashed into the paste from adjacent parts. Some have suggested I deviate from

bridging between 2 pads

Electronics Forum | Wed Nov 07 07:31:20 EST 2001 | steven

what is ideal or minimun spacing in between 2 pads to avoid bridging? thanks

Solder bridging after printing

Electronics Forum | Tue Jun 28 13:04:08 EDT 2005 | slthomas

Are you saying that increasing the frequency of cleaning to every 3 boards *reduced* bridging, or that it's just something you tried? I don't understand why that would help(in my experience it has reduced "insufficient solder" conditions but not brid

bridging between 2 pads

Electronics Forum | Wed Nov 07 17:10:15 EST 2001 | davef

If you don�t paste / reflow solder on the pads, they will never bridge. ;-) A design with a 0.13mm gap between pads will challenge equipment, materials, and process.

bridging between 2 pads

Electronics Forum | Wed Nov 07 18:37:27 EST 2001 | steven

sometime hand solder can cause also. no necessary have to be paste n reflow.:) now i'm facing bridging on 0402 components pads. any suggestions on spacing distance as we're going to re-design the pcb.

Solder bridging after printing

Electronics Forum | Sat Jun 25 10:04:08 EDT 2005 | ktron

Hi MSK, Stencil thickness: 5mils with laser cut Smallest pitch: 20mils Underscreen cleaning frequency: 10 bds per cleaning Note: We have decreased the cleaning frequency from 10 boards to 3 bds to reduce solder bridging after printing Regards,

  1 2 3 4 5 6 7 8 9 10 Next

bridging searches for Companies, Equipment, Machines, Suppliers & Information

High Throughput Reflow Oven

High Throughput Reflow Oven
Selective soldering solutions with Jade soldering machine

Benchtop Fluid Dispenser
Pillarhouse USA for Selective Soldering Needs

Component Placement 101 Training Course
Equipment Auction - Eagle Comtronics: Low-Use Electronic Assembly & Machining Facility 2019 Europlacer iineo + Placement Machine  Test & Inspection: Agilent | Tektronix | Mantis Machine Shop: Haas VF3 | Haas SL-20 | Mult. Lathes

Best Reflow Oven
PCB separator

Find a wide selection of nozzles, solder materials, storage solutions and more at SALESCON