Electronics Forum: camera (Page 106 of 128)

New Printer :- Dek Horizon 03i or MPM 125 ??

Electronics Forum | Tue Oct 14 19:03:54 EDT 2008 | diesel_1t

currently we have a new Horizon 02i, new software "instinctive" is pretty easy to program and operator friendly, i love to work with proflow. Gridlock is not working so good as they told. I don't like that the paper doesn't roll while you're under cl

AOI Joint Inspection

Electronics Forum | Fri Oct 17 14:26:39 EDT 2008 | hegemon

We use Mirtec MV-7s for post SMT inspection of solder joints as well. The artistry is in the program debug. We are very pleased with the solder inspections provided by these machines, and technology having advanced bit, most every AOI machine has t

NEW to Philips Topaz-X need help programming

Electronics Forum | Sat Nov 29 09:56:59 EST 2008 | blacksi27

What the other user was talking about is correct, converting it from gerber to machine cad. It is hard explaining programming SMT to a new user unless shown by another experience operator. I am also getting a topaz x pretty soon and I'll try to hel

Ultra low cost pick & place?

Electronics Forum | Thu May 15 23:13:26 EDT 2008 | sarason

The Essemtec has a very cheap to manufacture feeder which you could adapt, or try one of the feeders that remove the tape by "ploughing" it off. Can't recall the brand right now. They are well made, but very cheap to make. The laser gets you speed. T

MPM UP2000 HiE Z problem

Electronics Forum | Fri Aug 07 09:53:12 EDT 2009 | kpm135

The Z-axis Drive card on our MPM UP2000 HiE fried. We replaced it with a new card, setting all the jumpers to match the old card. After that we had to recalibrate the Z-axis and the snugger height but the problem is that the camera is now too close t

MPM AP25 Problems

Electronics Forum | Fri Oct 09 06:53:10 EDT 2009 | taus

Hello, I've recently started to work with MPM AP25, I began doing maintenance to get to know the machine. But now I'm having some problems in the teaching process. You can see the problem in the photo. http://img59.imageshack.us/i/image194p.jpg/

Researching placement machines - where do I start?!

Electronics Forum | Sat Oct 31 09:45:48 EDT 2009 | meritajs

Hello Jeffrey J I could share our experience in using used P& P machine type Philips (Yamaha) and Juki (Zevatech) We had three machines Philips (Yamaha) vintage about1990g, which work till now. They have same type of feeders, which is simple to find

Researching placement machines - where do I start?!

Electronics Forum | Mon Nov 09 12:06:36 EST 2009 | cellis

I am sure I know which video you are talking about with the 7722-FV shaking. It is a video where the camera was on the table next to the machine. It was not a sturdy table to begin with. This was done by one of our customers in NYC. It does make

AOI for solder inspection

Electronics Forum | Thu Oct 29 21:16:15 EDT 2009 | mah115

Fellows, We are considering getting an AOI machine to inspect boards that our vendors are giving us (we outsource the assembly of PCBAs). We have low volumes of boards, but every time a defect does slip by our human inspectors, it causes a lot of

AOI 2009 MIRTEC MV-7xi 5 MP or Yes tech YTV-FX 5MP

Electronics Forum | Mon Dec 21 12:09:21 EST 2009 | andrew_11

Hello Dany, i had been invloved in a evaluation at another company between omron,yestech,mirtec,vitech.. I found omron and vitech too long to program for hi mix low volumee. yestech and mirtec programmed quickly. I found the mirtec to find more of t


camera searches for Companies, Equipment, Machines, Suppliers & Information