Electronics Forum: check and off and pcb (Page 1 of 12)

Desiccants and pcb finish degradation?

Electronics Forum | Tue May 15 21:57:06 EDT 2001 | davef

Welcome!!! Where the hay ya been??? Sorry bud, were lining-up with your fab [it hurts me to say that, but when yer  ] We used to dry pack with desiccants, also. Its probably an old MIL-STD-2073-1C requirement [er something like that]. We qui

Desiccants and pcb finish degradation?

Electronics Forum | Mon May 21 17:32:23 EDT 2001 | davef

I said: "Our electronic circuit board fabricators seal the boards in moisture barrier bags [MBB]. We discontinued the use of desiccant bags in these MBB because of concerns about the desiccant releasing materials that would affect the solderability

x,y digitizer and optical comparator

Electronics Forum | Wed Feb 13 17:29:25 EST 2002 | Sheri Connor

I am looking for advice on sourcing a x,y > digitizer to create pick and place files, > off-line, rather than programming with the > machine. I could use original gerber data or > create the placement coordinates with the > digitizer. Also, refe

Printer and Reflow Oven Recommendations

Electronics Forum | Fri May 15 21:39:48 EDT 2015 | jlawson

Reflow.. 1.Rehm (Germany) - Best in Class Best overall process stability heating system ( Alot of makers have started to copy there VX heating arrangement ). COnveyor chains can be a bit more attention in terms of maintenance on rehm , but if foll

Flexi boards and uBGA

Electronics Forum | Thu Jul 06 13:36:37 EDT 2006 | SWAG

We've had much trouble with flex circuits. As previously mentioned, you must have local fids for the board or the BGA itself (if panelized). Other troubles we experience are drilled holes for pinned connectors. Unless the PCB manufactur has some w

Wave flux and profiling

Electronics Forum | Wed Dec 20 04:43:36 EST 2006 | greg york

Any decent flux would volatise off with the heat of the wave unless absorbed into the solder mask. Test this by trying to clean in alcohol or common solvent aerosol, if it does not clean then it is probably Mineral Salts from solder mask fillers. Ano

Wave flux and profiling

Electronics Forum | Mon Dec 18 23:24:50 EST 2006 | grantp

Hi, Yes, I would hate to resort to cleaning, but the product must be clean. We have been using palettes to keep most of the flux off the PCB, but there is still residue around the connectors. Does anyone suggest a good no clean flux to use with le

Pick and Place Rivet

Electronics Forum | Tue Aug 12 14:49:26 EDT 2008 | awegener

I'm attempting to pick and place a small rivet onto our PCB. The rivet should be attached via reflow solder. The rivet will be used to create a sandwich, holding together a frame and additional circuit board in a package. This part is intended onl

MPM Up2000 and SMEMA

Electronics Forum | Tue Sep 13 07:00:28 EDT 2016 | awhite

Thanks for the reply. When you hit start on the printer, you can see it send the "start cycle (SMEMA)" signal, and it immediately goes to "awaiting board from upstream." This tells me that the printer knows a signal has definitely been sent and rece

Wave and Reflow Profiler

Electronics Forum | Tue Feb 19 16:19:26 EST 2008 | edatasys

Check out http://www.solderstar.co.uk/wavePro.html This tool measures all key wave solder information with a single pass. Wave/PCB contact, immersion depths, etc. Also has a reflow pack to allow use on reflow, 9 channels with predictive software. B

  1 2 3 4 5 6 7 8 9 10 Next

check and off and pcb searches for Companies, Equipment, Machines, Suppliers & Information

Precision PCB Services, Inc
Precision PCB Services, Inc

Products, Services, Training, and Consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep & Sole Agent in North America for Shuttle Star BGA Rework Stations.

Training Provider / Service Provider / Manufacturer's Rep / Equipment Dealer / Broker / Consultant

1750 Mitchell Ave.
Oroville, CA USA

Phone: (888) 406-2830

Equipment Auction - Ex-Eolane Montceau

High Throughput Reflow Oven
SMT feeders

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.


Inspection mirrors for electronic rework and repair.
PCB Depanelizers

ONLINE IPC Training & Certification