Electronics Forum: chinese and cutting (Page 2 of 15)

Neoden and YX chinese pick and place machines, looking for users opinions

Electronics Forum | Wed Feb 24 14:52:43 EST 2021 | spoiltforchoice

Well to their credit Neoden has regional representation in the EU, Aus and USA which helps support the end user better than email/QQ chats to China, although how much they really can do on their own is not something I could speak for. I suppose for

Neoden and YX chinese pick and place machines, looking for users opinions

Electronics Forum | Wed Feb 24 10:57:52 EST 2021 | spoiltforchoice

And then they make a new machine, and start the software all over again, or change the hardware so much the older model doesn't get any of the software tweaks on the new one even if they are supposedly the same model.... Neoden bigger machines shoul

Neoden and YX chinese pick and place machines, looking for users opinions

Electronics Forum | Wed Feb 24 14:19:24 EST 2021 | marcelorotofrance

I am completely aware about the lack of kilos, other goodies and buggy software. I scratch my head when I read that they claim that they can do 0201 with belt drives and without linear encoders. In my personal opinion a KE family Juki would be perfec

small and good pick and place machine

Electronics Forum | Thu Sep 05 23:18:03 EDT 2013 | feiyangniao

There is a new toy I received today: a NeoDen TM-240A automatic desktop pick and place machine! I’ve kept my eyes on this baby for a quite a while, and finally decided to make a purchase last week. The shipping was very fast: DHL from China, a total

Inspection and splicing

Electronics Forum | Thu Dec 21 13:11:25 EST 2006 | SWAG

We have fought with cut-tape way too much. It's always a bad idea. We've tried a couple methods/devices for manual splice with limited success. Before you look into this I would ask them if they could supply you cut tape qty's inslusive of fairly

Inspection and splicing

Electronics Forum | Tue Aug 21 08:34:03 EDT 2007 | rgduval

We have the same problems with cut/tape parts. But, we specialize in short-run prototypes, so I don't have much of a choice but to deal with it, and find a way to make it as easy as possible. We just demo'd a splice tool from Sierra Electronics (ww

Pad and Stencil Design

Electronics Forum | Tue Sep 18 15:35:23 EDT 2001 | jschake

A laser cut stainless steel stencil was used exclusively for the evaluation of the complete 0201 assembly process, which addressed printing, placement, and reflow. However, I have also conducted off-line 0201 print tests using a nickel electroformed

Mydata Pick and place

Electronics Forum | Wed May 09 10:39:03 EDT 2001 | davef

The two first level cuts at comparing placement machines are: * Placement rate * Range of component capabilities This boils-down approximately to machine price. Virtually, everyone's feeders are priced similarly. Go to "Circuits Assembly" magazine

Stencil cleanliness and inspection

Electronics Forum | Thu Jun 07 16:33:22 EDT 2001 | davef

I too know of no product like you desire, but I have a lead for you to follow that might get you further than you're getting now. Call Lumonics [Lumonics, 130 Lombard St, Oxnard, CA 93030 805.485.5559 fax3335 http://www.gsilumonics.com]. They ma

Inspection and splicing

Electronics Forum | Thu Dec 21 08:31:32 EST 2006 | Karkanov

Hi, Do you have any idea if there is some tool to inspecet if we have the right component on the board ? like a smart tweezer. Also I'm looking to find a tool to spice smt reel. I need that because our buyer told us they will only buy cut tape.


chinese and cutting searches for Companies, Equipment, Machines, Suppliers & Information

Online IPC Training & Certification

ONLINE IPC Training & Certification
fluid dispenser

MSD Dry Cabinets
Selective Conformal Coating System

Easily dispense fine pitch components with ±25µm positioning accuracy.
Solder Mask & Low Stand-off Component Cleaning

Best Reflow Oven
Assembly Automation Technology

ARE HUMIDITY INDICATORS PART OF YOUR SUPPLY NETWORK? Register for the webinar!