Electronics Forum: clear and alarms (Page 1 of 8)

ITAR and AS9100...like peas and carrots?

Electronics Forum | Wed Aug 12 16:41:20 EDT 2009 | JWPlainview

Thanks for clearing that up, Dave. We've been getting a lot of inquiries citing both certifications. Just thought there might be a link between the two.

CP4 jerks all axis after power up and reset sw...

Electronics Forum | Tue Apr 17 13:07:17 EDT 2012 | rodrigo

Well... after much headache I found a bad relay contact in M1CR1E. The good news is somehow the axis are no longer jerking. The bad news is that it still does not work. When I turn it on now it shows this: emergency stop (in red) waiting for reset

via tenting and pluging

Electronics Forum | Fri Nov 03 02:32:56 EST 2006 | shivam

HI ALL, can anybody clear me what is via tenting and via pluging?? second one, if i use via in pad for an.5mm bga what care i should taken, what should be the soldermask open in top and innerlayers for via?how it will directly connect to top layer


Electronics Forum | Fri May 23 15:31:46 EDT 2003 | daanterstegge

Hi ChrisX, DPMO = number of defects per million opportunities. PPM (parts per million) is exactly the same, although the terminology is less clear about what it means. SPC(statistical process control) is a methodology based on statistical technique

UPS and ROHS Compliance

Electronics Forum | Fri Jan 27 09:48:26 EST 2006 | patrickbruneel

GS UPS are exempt for 2 reasons: A. Lead in solders for servers, storage and storage array systems, network infrastructure equipment for switching, signaling, transmission as well as network management for telecommunications. B. The primary functi

Problems with the Estop in 1809 exl

Electronics Forum | Thu Apr 26 02:32:44 EDT 2018 | bukas

1. check both e-stop buttons are released 2. reset e-stop with blue reset button 3. open Alarms menu(there is icon) 4. acknowledge alarms(next to alarms menu icon) 5. clear alarms(next to acknowledge alarms icon) 6. go back to operating interface(thi

Geometric Dimensioning and Tolerancing

Electronics Forum | Sat Jun 06 09:53:59 EDT 1998 | Earl Moon

GEOMETRIC DIMENSIONING AND TOLERANCING (GDT) Using and applying GDT to printed circuitry and assemblies is very much like applying it to any other design for manufacturing (DFM) or design for assembly (DFA) requirement using concurrent engineering (C

Solder and flux

Electronics Forum | Wed Nov 06 05:13:01 EST 2002 | Dreamsniper

Crystalline flux if it is really clear should not be a problem. We were using Amtech paste before and we have the same results. Sometimes we mistakenly see it as a dry joint because of the reflections from the lighting of our Metcal inspection system

UPS and ROHS Compliance

Electronics Forum | Fri Jan 27 15:39:08 EST 2006 | GS

Thanks Patrick yes I feel better now, but allow me a comment: Reason A: your answer confirms my tough. In general could be accepted Reason B: your answer "The primary function of ups start when electricity is "off" so the equipment is clearly exem

Component Obsolescence and Availability

Electronics Forum | Thu Apr 07 19:17:43 EDT 2022 | cbart

Good afternoon The ISI I was mentioning is interconnections solutions which is a division of Molex. a few years back we ran into a component end of life situation but had thousands of very high dollar bare boards in stock. the package was a BGA and w

  1 2 3 4 5 6 7 8 Next

clear and alarms searches for Companies, Equipment, Machines, Suppliers & Information

Sell Your Used SMT & Test Equipment

Real Time Process Control BREAKTHROUGH for Dispensing Industry.
Void Free Reflow Soldering

World's Best Reflow Oven Customizable for Unique Applications
thru hole soldering and selective soldering needs

World Source Equipment: Used equipment sale. Hundreds of items on sale.
PCB Depanelizers

Low-cost, self-paced, online training on electronics manufacturing fundamentals