Electronics Forum: cms400 and settings (Page 1 of 25)

Max and Min nozzle settings on CP7

Electronics Forum | Tue Jul 20 04:16:02 EDT 2004 | Charles Huang

Wondering if there any CP7/F4G programmers out there that can help me out with this one. I'm assuming the setting for max and min nozzle in the "environment" section of the part data would allow me to use either the specified max OR min nozzle in th

Max and Min nozzle settings on CP7

Electronics Forum | Mon Aug 02 13:06:10 EDT 2004 | jbabson1

If the CP7 is like the CP643, it defaults to the MAX size unless that nozzle is skipped. Then it would switch to the next smaller nozzle on that head.

Max and Min nozzle settings on CP7

Electronics Forum | Sat Jul 24 04:02:18 EDT 2004 | kent_peterson

Two ways at it.You could just put the same nozzle for both the min and max.Or you could move the feeder into a location that has similar parts using the nozzle you want. With the feeder setup it should be optimized for the least amount of nozzle ch

Max and Min nozzle settings on CP7

Electronics Forum | Sat Jul 24 04:02:21 EDT 2004 | kent_peterson

Two ways at it.You could just put the same nozzle for both the min and max.Or you could move the feeder into a location that has similar parts using the nozzle you want. With the feeder setup it should be optimized for the least amount of nozzle ch

Re: WAVE SOLDERING and Gluing 0603 packages

Electronics Forum | Sat Apr 24 04:41:56 EDT 1999 | Murray Pulman

Dear C.K We are routinely wave soldering 0603 and sot23 on subcontract, hence we get what we are given!!. Being UK based we use a Blundell cms 400 dual wave soldering machine (made in Coventry), Tecan Stencils and Loctite 3612 adhesive. You must k

small and good pick and place machine

Electronics Forum | Thu Sep 05 23:18:03 EDT 2013 | feiyangniao

There is a new toy I received today: a NeoDen TM-240A automatic desktop pick and place machine! I’ve kept my eyes on this baby for a quite a while, and finally decided to make a purchase last week. The shipping was very fast: DHL from China, a total

Stencil cleanliness and inspection

Electronics Forum | Wed Jun 06 21:19:41 EDT 2001 | davef

Consider running two sets of stencils and washing every four hours.

Touch-up and Inspection Process

Electronics Forum | Wed Mar 02 18:46:02 EST 2005 | Austinj

The tendancy always has been "when in doubt, touch it up"... this is not the way to "verify the process" and is not the best strategy for multiple reasons (unessecary rework, additional labor costs, as well as making the solder joint more brittle, [i

tape and reel machine

Electronics Forum | Fri Mar 24 15:20:27 EST 2000 | Chris McDonald

I have recently purchased a Tape and reel machine from V-Tech. We are using Presure Sensitive tape and we are not geting good results. Anything bigger that a SOIC14/16 gives us trouble. The cover tape will pull off on the feeder and we will lose part

Skewed and popped components

Electronics Forum | Tue Sep 23 23:19:34 EDT 2003 | RLW

If you have a board that you've run several times, now you run it and like before all settings are the same, but now you have 0603's randomly skewed or an inch or so away from their intended pad (as if popped up in the air), or an occasional 7343 cap

  1 2 3 4 5 6 7 8 9 10 Next

cms400 and settings searches for Companies, Equipment, Machines, Suppliers & Information

SMT & Related Equipment - Delta Tau Data Systems Inc.

World's Best Reflow Oven Customizable for Unique Applications
pressure curing ovens

Want to know where to find the best AOI system? - Read testimonials.
thru hole soldering and selective soldering needs

Benchtop Fluid Dispenser