Electronics Forum: coding (Page 56 of 84)

help GSM2 Spindles error: All spindles safe sensor not seen for head

Electronics Forum | Thu Mar 20 11:30:58 EDT 2014 | dave222

Hello Again. I little more information about the issue: when trying to zero machine head the spindles move up and down about 6 times before giving the error code. also I notice that all the LEDs on the circuit board are off. L11 - L18. and the nume

Lite-On side looking LED assembly problems

Electronics Forum | Fri May 30 20:03:14 EDT 2014 | hegemon

Starting with the manufacturers layout is a good start. Tilted parts, bad solder joints, sounds like a wetting issue and the board or the parts. Insufficient solder sounds like the printing process needs some attention. We have used this part in th

MY12 F-MOT-MSETDYN x/12: Position Counter Dead

Electronics Forum | Wed Sep 03 15:18:12 EDT 2014 | chemers

I am looking for some help for where to look to fix this MY12 problem. We started the machine after the weekend and this error code comes up during initialization. F-MOT-MSETDYN X/12: Position counter dead MyData tells us our only option is to have

Identify SMD IC

Electronics Forum | Mon Jan 12 14:54:58 EST 2015 | nkrcompany

Hi All, I would like to ask some help from you. It would be very important for me to identify a bad IC. It is located in a 2,4GHz radio frequency receiver, maybe the IC is some kind of low noise amplifier, but I'm not sure about it. It has 5-pin, see

NOVASTAR Tune menu password

Electronics Forum | Fri Dec 18 20:27:44 EST 2015 | rowsail

Thanks, I was able to get a PDF of the manual which describes: 1. INSTALL EXTERNAL THERMOCOUPLE PROBE. 2. TURN ON MAIN POWER: a. Press ENTER button b. Press F1 or F2 to scroll to SET UP mode c. Press F3 to select SET UP mode d. Display will read EN

need help identifying these marking codes!

Electronics Forum | Tue Jan 20 04:43:33 EST 2015 | gragal

I need to replace a device which is in a 6-pin package which looks like SOT 23-6 / SC-74 style. The markings are D102/ 214B (D102 above 214B). I have checked numerous references to no avail. I think that the device is a comparator or op-amp with V

Electrovert Bravo 4050 Help

Electronics Forum | Fri Jan 23 15:57:12 EST 2015 | rgduval

Anyone out there have one of these Electrovert/Speedline ovens? Our PLC lost its mind, and we're looking to get it back. Speedline doesn't support the oven anymore, so, getting the file out of them doesn't seem likely. The PLC is Mitsubishi FX2N48

Quad IVc says

Electronics Forum | Thu Feb 26 12:58:21 EST 2015 | daniel_esposito

Hi everyone! I have P&P Quad IVc. The Hand Held Terminal (HHT)says "V idle" intead of "V ENTER CMD", and when it is running, the HHT shows commands lines each one at the same time it is running. One of our technician entered mistakenly, at the HHT,

DQFN INSUFFICIENT SOLDER / HEAD ON PILLOW

Electronics Forum | Fri Mar 06 12:02:36 EST 2015 | saoasasd

So far we have tried diferent date codes, solder pastes and PCBA models (same component used in different projects). We have also sent some components for plating analysis and we are waiting the LAB feedback. Additionally, we have tried components wi

Topaz-Xii Error Code 30

Electronics Forum | Mon Apr 27 11:29:06 EDT 2015 | chris_jayconsystems_com

When I do the adjust to make sure the vision and tolerance is working it works perfectly. But if the machine runs a board I am riddled with this. I have checked the vacuum levels on all the heads and they are within where they are supposed to be for


coding searches for Companies, Equipment, Machines, Suppliers & Information