Electronics Forum: controller 2 link failure (Page 1 of 10)

DEK 265LT problem

Electronics Forum | Mon Jul 30 17:31:59 EDT 2018 | dekhead

That error message is keyed by a hardware (soldered) link on the backplane board of the Y1 (motor controls), through direct cable to PCIB40#3... check connections both ehds; possibility of multiple PCIB failures?

DEK 265 boot error

Electronics Forum | Thu Oct 26 12:14:34 EDT 2017 | lefwan

Our DEK 265 machine is showing this error message during starting…than it keeps re-starting in endless loops: Diskette drive failure on drive A Fixed Disk Controller Failure Fast ready check - Version 1.0 Copyright Arcom Control Systems Ltd. CMOS

DEK 265GS - Vision hardware error

Electronics Forum | Tue May 28 12:56:22 EDT 2019 | dekhead

It is a communications failure between the CPU and the Cognex card. Does comms initiate between the 2 cards (flashing green on both)? or does it immediately come up red LED on Cognex? Have you reseated the CPU board as well as the Cognex? Is this a s

reliability of oxidized SMT parts soldered with SnPb

Electronics Forum | Thu Jun 28 09:38:14 EDT 2012 | 14367

PSMN130-200D MOSFET TRANSISTOR D2PAK - failure of some parts led to investigation, oxidization or surface contamination was noticed on remaining parts. The surface contamination could be removed when fingernail was drawn over the bottom terminating s

reliability of oxidized SMT parts soldered with SnPb

Electronics Forum | Thu Jun 28 09:38:20 EDT 2012 | 14367

PSMN130-200D MOSFET TRANSISTOR D2PAK - failure of some parts led to investigation, oxidization or surface contamination was noticed on remaining parts. The surface contamination could be removed when fingernail was drawn over the bottom terminating s

Vitronics XPM820 Alarm - Power Failure

Electronics Forum | Fri Jan 12 09:22:51 EST 2018 | dskling

Hello We have a Vitronics XPM820 that has us stumped. We have replaced both power supplies (G1 and G2) and we still cannot clear this alarm. The A1 board has all 4 leds light for proper voltages. We have verified that we are getting the correct vo

NASA-UA report update

Electronics Forum | Mon Oct 03 10:41:57 EDT 2011 | patrickbruneel

Some of us here attended the 5th CALCE international symposium on tin whiskers http://www.calce.umd.edu/symposiums/ISTW2011.htm where one of my former professors, Dr. Henning Leidecker, talked about the tin whiskers he and the others at NASA Godda

DEK 265 motor com error, axis 1,2,3 fatal error

Electronics Forum | Wed Aug 24 09:20:25 EDT 2016 | dekhead

Suspect comms link error from Y3 to Y1 crate. COM 2 off of CPU, depending on board. If CPU board has RS485 port it is direct to back panel of PC; if older board it only has RS232 and thus requires 232/485 converter board (internal to PC). then direct

Incoming Water Quality

Electronics Forum | Mon Jun 11 22:06:00 EDT 2001 | davef

The issue is not the cleanliness of your in-bound water. The issue is the cleanliness of the board your customer receives. Look at J-STD-001C, Para 8, "Cleanliness Requirements". The end product cleanliness is the end result of your: * In-bound

Re: Pin Hole/Blow Hole - Causes and cure please

Electronics Forum | Fri Jun 25 01:11:31 EDT 1999 | Vinesh Gandhi

Recently, there has been an upsurge in the Pin Hole/Blow Hole problem in our wave soldering process. We are baking the PCBs for 2 Hrs. at 125 degree C. The Wave Soldering profile seems to be O.K. Still the problem is persistent. Can somebody

  1 2 3 4 5 6 7 8 9 10 Next

controller 2 link failure searches for Companies, Equipment, Machines, Suppliers & Information

Voidless Reflow Soldering

Benchtop Fluid Dispenser
Dual Lane Reflow Oven

One-stop Platform For All Your Need For SMT - QYSMT
Used PCB Assembly Equipment & SMT Equipment

High Resolution Fast Speed Industrial Cameras.