Electronics Forum: count and on and tool (Page 1 of 2)

Im trying to install a tool on a MY15 and I am getting errors

Electronics Forum | Thu Aug 05 17:37:28 EDT 2021 | SMTA-64387687

Did you grease the tool o-rings? If they are too dry, the head won't slide onto the tool. Also, make sure the tools are flat in the tray. I'm assuming that you aligned on the center of the tool. And, try cycling the non-spring tools, like A24, to see

Im trying to install a tool on a MY15 and I am getting errors

Electronics Forum | Wed Aug 04 18:12:27 EDT 2021 | tomdegas

I am trying to install an A12 tool on my MY15 and I get the following error: "F-TLMN-9: Failed preliminary fetch during installation" I looked it up and it says Operator error and that the tool is missing. The tool is in the tray and the MY15 picks

Im trying to install a tool on a MY15 and I am getting errors

Electronics Forum | Thu Aug 05 17:32:31 EDT 2021 | cyber_wolf

Including non-spring tools ? Additionally I assume you know how to use the tool install utility and have looked for things like cracks in the big ribbon cables on the X ? Tools are not dry and have white grease on them etc ? There is a show force

Im trying to install a tool on a MY15 and I am getting errors

Electronics Forum | Fri Aug 06 17:19:46 EDT 2021 | SMTA-64387687

It seems to me that something is out of calibration. I noticed that you were reinstalling TPSys. Did this start after the reinstall? Did you restore a backup of your parameters, or recalibrate the machine with new values? Try changing the tools to "n

Im trying to install a tool on a MY15 and I am getting errors

Electronics Forum | Wed Aug 04 23:32:05 EDT 2021 | tey422

Seem like sensor failed to detect the tool is fetched. You might want to try to clean the inside barrel of the fetch tool. Use the foam swab, to clean it. If it's a spring loaded tool that you trying to install, you have to make sure the top of the

Im trying to install a tool on a MY15 and I am getting errors

Electronics Forum | Fri Aug 06 14:01:53 EDT 2021 | tomdegas

Unfortunately all my tools are spring loaded. Yes I do know the tool install utility. I have been running and maintaining the 3 MyData machines for over 20 years and I never saw an error like this. I grease our tools once a month so I know that is

Im trying to install a tool on a MY15 and I am getting errors

Electronics Forum | Thu Aug 05 17:23:22 EDT 2021 | tomdegas

I just tried and I am getting the same error for all the tools.

Im trying to install a tool on a MY15 and I am getting errors

Electronics Forum | Wed Aug 18 13:48:12 EDT 2021 | rgduval

It's been awhile, but, some other things you might look at: - Check the fiducials on the toolbox. If they're getting obscured/damaged, all kinds of weird things can happen. I had problems initializing tools one time because of this, and I could actu

Im trying to install a tool on a MY15 and I am getting errors

Electronics Forum | Thu Aug 05 15:06:02 EDT 2021 | tey422

The last time I work on the Mydata machine was like over 15years ago. Sorry, I couldn't provide much more help than what I could remember so far.

Im trying to install a tool on a MY15 and I am getting errors

Electronics Forum | Thu Aug 05 17:19:26 EDT 2021 | cyber_wolf

Will it pick up an A13 or A14 ?

  1 2 Next

count and on and tool searches for Companies, Equipment, Machines, Suppliers & Information

Count On Tools, Inc.
Count On Tools, Inc.

COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.

Manufacturer

2481 Hilton Drive
Gainesville, GA USA

Phone: (770) 538-0411