Electronics Forum | Fri Sep 11 13:49:34 EDT 1998 | BILL
DEAR SIR, I WANT TO CALIBRATE THE RELOCATED THE WIDE WIDE & NARROW VIEW CAMERA OF FUJI CP-4-1 WITH SMD 3 VISION SYSTEM, SEEMS I HAVE /CAN CALIBRATE THE CP-4-1 WITH SMD 2 VISION SYSTEM ONLY. I BELIEVE IF THE VISION SYSTEM UPGRADE FROM SMD 2 TO SMD3,
Electronics Forum | Tue Sep 22 19:02:29 EDT 1998 | Matt
| DEAR SIR, | I WANT TO CALIBRATE THE RELOCATED THE WIDE WIDE & NARROW VIEW CAMERA OF FUJI CP-4-1 WITH SMD 3 VISION SYSTEM, SEEMS I HAVE /CAN CALIBRATE THE CP-4-1 WITH SMD 2 VISION SYSTEM ONLY. I BELIEVE IF THE VISION SYSTEM UPGRADE FROM SMD 2 TO SM
Electronics Forum | Wed Nov 13 14:55:42 EST 2013 | jimmyboz
The CP4 will place them all day with no rejections. If they are small target the CP4, if they are large, select the GSM.
Electronics Forum | Tue Jul 14 21:31:19 EDT 1998 | Wen-han Tan
We just have a use cp4 .I have a problem on transfering data between cp3 to cp4 .when I use the data for cp4 I can't have parts in correct location. Is that normal? or it's because that has a different vision system.if so.how can i do with it.the dat
Electronics Forum | Wed Jul 15 06:32:03 EDT 1998 | Process Engineer
| We just have a use cp4 .I have a problem on transfering data between cp3 to cp4 .when I use the data for cp4 I can't have parts in correct location. Is that normal? or it's because that has a different vision system.if so.how can i do with it.the d
Electronics Forum | Mon May 01 10:26:14 EDT 2000 | Mike Naddra
I Have approximately 150-200 Fuji Cp4-3 8x4mm 1.0 TLC, LARGE Tail feeders. I am looking for an even trade for Fuji Cp4-3 8x4mm 1.0 TLC, SMALL Tail Feeders. If anyone is interested Please respond. Thanks, Mike Naddra
Electronics Forum | Thu Sep 10 09:21:27 EDT 1998 | Y.F. Michael Kou
| We are using PCBs of CEM3 Material with bare copper fiducials. The whole | board is of bare copper with a lacquer coating (Coats brother S2974). | The fiducials are of 1 mm diameter bare copper. we use Panasert MV2F as | well as Fuji CP4-3. In bo
Electronics Forum | Thu Dec 09 13:22:24 EST 2010 | rodrigo
Hi All, I'm trying to use the F4G CP-4 optimizer. I cleared all the issues I was having except for this error I get at the end: Execute, 2030: Cycle Time table file not found I see a file in one of the folders named CP4_CYC.TBL but I'm not sure if
Electronics Forum | Wed Nov 24 07:02:15 EST 1999 | JAX
Larry, Carl's right about vision 254 and 255 but I believe CP4's can be set up to check for a part on the nozzle,(parts check sensor)like any other CP. This could be activated to make sure parts are being placed. Then again CP4's might not ha
Electronics Forum | Thu Jun 29 09:13:02 EDT 2006 | MarkM.
I am looking for bulk of parts for a CP4/CP43. If you are sitting on those old CP4 parts and tired of wiping the dust off please let me know so we can discuss so I may get them from you. Also listed this in marketplace already as well. mmjm_1099@ya
