Electronics Forum: cp6 hardware ng (Page 1 of 2)

Fuji F4G PC hardware requirements?

Electronics Forum | Mon Apr 09 15:02:00 EDT 2018 | rodrigo

Hi all, Does anyone know the "preferred" PC setup to install F4G? We have several PCs but it only fully works on an old celeron PC that is extremely slow. In most other either the CP6 optimizer or CAD converter do not work. We have 2 lines with the s

CP6-4000 FUJI TECH in CALIFORNIA???

Electronics Forum | Fri Jul 17 19:43:20 EDT 2009 | fujiphil

Have you eliminated the hardware N.G.? Check the connection for the rear door. If the connection are ok, try to bypass the key. short the two wires for the rear door. If the rear door problem is corrected, check the rear door switch physically. Reg

FUJI CP65 Hardware NG

Electronics Forum | Fri Jan 17 19:29:09 EST 2014 | mdang

Hi, My FUJI CP65 is working last couple of month. Last week, it display "Hardware NG" message when I power on. I can not find this msg in the manual. Does anyone has experiences with this to point me where I should look? Thanks, -Michael

CP6-4000 FUJI TECH in CALIFORNIA???

Electronics Forum | Mon Jul 13 10:04:06 EDT 2009 | csm

Dear all, we have an Fuji CP6-4000 we get some weeks ago, but it shows an error "Hardward NG and show some actions (Inch the axis to cancel the overtravel. Then switch the power off and restart the machine). We did but display same error. I would li

FUJI CP65 Hardware NG

Electronics Forum | Sat Jan 18 12:07:44 EST 2014 | jimmyboz

Oh yeah, the x-motor cooling fan too.

FUJI CP65 Hardware NG

Electronics Forum | Mon Jan 20 11:59:54 EST 2014 | mdang

Hi Jimmy, Here is my email address mdang@sigmatronix.com. Thanks, -Michael

Fuji CP642 Hardware NG issue

Electronics Forum | Mon Apr 21 10:34:39 EDT 2014 | cyber_wolf

I think we traced it down to the sensor on the x-axis motor.

FUJI CP64 Service in San Diego CA area

Electronics Forum | Mon Jul 13 09:34:32 EDT 2009 | csm

Dear all, we have an Fuji CP6-4000 we get some weeks ago, but it shows an error "Hardward NG and show some actions (Inch the axis to cancel the overtravel. Then switch the power off and restart the machine). We did but display same error. I would

FUJI CP65 Hardware NG

Electronics Forum | Sat Jan 18 12:03:54 EST 2014 | jimmyboz

Hi, > > My FUJI CP65 is working last couple of > month. Last week, it display "Hardware NG" > message when I power on. I can not find this msg > in the manual. Does anyone has experiences with > this to point me where I should > look? Thanks, -

Fuji CP642 Hardware NG issue

Electronics Forum | Tue Apr 08 08:01:35 EDT 2014 | cyber_wolf

So we had a ringblow pump blow up in our CP642. We replaced it and now we are getting hardware NG errors very intermittently.(2-4 times during and 8 hour shift) I see that the x-motor fan, cam motor fan,and oil cooler are all in this circuit. When i

  1 2 Next

cp6 hardware ng searches for Companies, Equipment, Machines, Suppliers & Information

convection smt reflow ovens

Component Placement 101 Training Course
2024 Eptac IPC Certification Training Schedule

Reflow Soldering 101 Training Course
2024 Eptac IPC Certification Training Schedule

Best Reflow Oven
Global manufacturing solutions provider

Training online, at your facility, or at one of our worldwide training centers"
Professional technical team,good service, ready to ship- Various brands pick and place machine!

Low-cost, self-paced, online training on electronics manufacturing fundamentals