Electronics Forum: datapaq and troubleshoot (Page 1 of 3)

Wave and Reflow Profiler

Electronics Forum | Mon Feb 18 15:44:49 EST 2008 | ck_the_flip

Yup! All the major players out there - KIC, Datapaq, and ECD - are all capable of profiling both reflow and wave solder. check them out. www.kicthermal.com www.ecd.com www.datapaq.com

Wave and Reflow Profiler

Electronics Forum | Tue Feb 19 05:00:07 EST 2008 | muarty

We have used both Datapaq and ECD Mole in the past. Either system will do the job for you, slight preference would be for the ECD system.

Wave and Reflow Profiler

Electronics Forum | Tue Feb 19 09:41:26 EST 2008 | slthomas

ECD sells the MOLE, and they sell both the Oven Rider and the Wave Rider to accompany it. The thing is, you can profile both an oven and a wave machine without either if you're willing to just solder your thermocouples to a board. The nice thing ab

Flux Designations and Composition

Electronics Forum | Tue Jun 29 14:42:55 EDT 2004 | davef

You're correct, for every dumpster full of paper written about solder, there's a sentance written about fluxes. There's dribs and drabs about fluxes in most of the soldering books [ie, Manko, Klein-Wassink, Judd, Strauss, etc] and most of that is ve

Lead Free and ICT

Electronics Forum | Sat Jun 03 03:35:16 EDT 2006 | mika

Yes we do have a problem with this. We have by now investigate numerous lead/RoHS PCBA:s The RoHS boards are by far the most difficult one's to probe and test. Our people at the "test area" including Flying Probe and ICT they spend a lot of time to t

MPM Up2000 and SMEMA

Electronics Forum | Tue Sep 13 10:00:27 EDT 2016 | awhite

Switched out the mech. relay on the board loader, no change. Same behavior. Could not find a mech. relay on the printer... SMEMA wiring appears go directly to a PCB. And it is at that point that I run out of talent. If the machine weren't dedicate

Circuit cam and mydata

Electronics Forum | Fri Mar 27 12:46:23 EDT 2020 | unisoft

Unisoft has been import gerber only for years to setup assembly, aoi machines, etc. *** Help for Importing GERBER only files for used in programming Assembly, AOI, Test, Selective Soldering machines (X/Y Center, Rot, Part#). Also allows you to cre

Machine and Vision Troubleshoot Guide

Electronics Forum | Mon May 13 11:07:02 EDT 2002 | stefwitt

I hope, I can contribute with this quick reference trouble shoot guide. http://www.geocities.com/stefwitt/trouble.html http://www.geocities.com/stefwitt/Vision.html

PCB Test and Troubleshooting Rates

Electronics Forum | Tue Mar 25 10:11:03 EDT 2008 | bandjwet

We recently sent some PCB assemblies along with the schematics to a test services provider. Afer paying for the NRE tooling charges we were paying $75.00 per hour for the service providers Level 1 test technicians. Does this sound like a fair rate (w

wave soldering and solder bridge

Electronics Forum | Mon Dec 17 13:58:54 EST 2007 | ck_the_flip

I made my own wave measuring device using KIC2000 system. KIC2000 has automatic wave detection, so now I have a profiler for both reflow ovens and wave solder. The delmat carrier only cost $500. A guy, Samir, from this forum gave me the idea, actu

  1 2 3 Next

datapaq and troubleshoot searches for Companies, Equipment, Machines, Suppliers & Information