Electronics Forum: delta wave solder pump (Page 1 of 27)

soltec delta wave

Electronics Forum | Wed Oct 21 13:50:50 EDT 2020 | kierantennant

hi, I am experiencing a problem with our wave solder machine where zone 2 (forced convection) fan will not work when called upon. so we swapped it with zone 3 to make sure the motor was not at fault and it wasn't so we moved the A1 into a different 2

Seho 1135C Wave Solder can't generate sufficient delta wave height

Electronics Forum | Thu Sep 26 23:14:25 EDT 2013 | zsoden

We picked up this old (circa late 80s) Seho 1135 machine last year for next to nothing. It needed a bit of TLC to bring it back to working order but it's 99% working now. The only problem left is that we cannot get sufficient height from the delta wa

Rebuilding Electrovert Solder pump motors...

Electronics Forum | Mon Feb 28 11:24:13 EST 2005 | EHess

Still looking for a second source for the Electrovert Econopak II wave solder pump motors, or a place that rebuilds them. anyone? Anyone? Beuhler?

Rebuilding Electrovert Solder pump motors...

Electronics Forum | Tue Feb 08 06:28:04 EST 2005 | teilo

We manufacture retrofit kits completley out of titanium for all types of Wave Solder Machines, we also manufacture titanium fingers. Avoid solder overflow damage with titanium board stiffners. Also we manufacture board carriers. We have already supp

vitronics delta backplate

Electronics Forum | Wed Feb 06 02:14:43 EST 2008 | mun4o

Hi, we use Vitronics Delta 6622 solder wave.I try to adjust high of backplate, but I don't know whether the adjustment is correctly.Now, when the frame enter in the main wave, solder flow in the same direction as PCB.But when the frame go above main

What is delta t?

Electronics Forum | Thu Oct 25 11:29:04 EDT 2007 | ck_the_flip

Forget all the bickering and semantics. EVERYONE IS RIGHT!! ...but then again, in soldering, there IS no right, wrong, or indifferent... just blame. :-) Soldering is, after all, the most difficult process with the most opportunities for defects.

vitronics delta Wave solder software version fail

Electronics Forum | Tue Sep 17 13:58:56 EDT 2013 | smtventasmex

i have a vitronics Delta 6622CC with a software fail, i turn it on and when i open the software on the CPU, it enter but show me a message of wrong vertion, and then i choose ok and software close it self, let me know if some one of you have this fai

wave solder

Electronics Forum | Mon Jun 12 10:57:51 EDT 2000 | Jason

I am new to wave soldering. Any information is greatly welcomed. Here is the problem. After soldering the boards they have a film on the bottom of them and sometimes a white powder looking substance. I have tried decreasing the amount of flux on

Delta wave solder

Electronics Forum | Tue Oct 11 14:02:59 EDT 2016 | mnorthey

We have a slider Bar on the back side of our Delta Wave. It is adjustable and slides up and down (adjusting bolt) on the back edge of the Lamda Wave to prevent this problem; keeping the trough behind the Lamda is essential as well. Along with attenti

Delta wave solder

Electronics Forum | Mon Jun 12 07:52:21 EDT 2017 | tch

We have had this issue on our Delta 3 waves and determined that there are small pin holes in the solder pot. We had plates welded to the outside of our solder pot on the lead free wave and this bought us enough time until we could replace the wave, a

  1 2 3 4 5 6 7 8 9 10 Next

delta wave solder pump searches for Companies, Equipment, Machines, Suppliers & Information

SMT feeders

Repair tools for all your electronic circuit board repair needs.
Panasonic CM402, CM602, DT401

Easily dispense fine pitch components with ±25µm positioning accuracy.
Electronics Decoating Agent

Best Reflow Oven