Electronics Forum: detached (Page 1 of 5)

BGA Detached off the board

Electronics Forum | Mon Aug 11 09:21:04 EDT 2008 | davef

Sounds like solder is not taking to the pads of the BGA interposer. Check the solderability of the component.

BGA Detached off the board

Electronics Forum | Mon Aug 11 10:55:43 EDT 2008 | realchunks

RoHS BGA. No lead in it.

BGA Detached off the board

Electronics Forum | Mon Aug 11 07:27:32 EDT 2008 | eyalg

We had experienced two (2) A BGA which fail (detached) off the board. Surprisingly we noticed that most of solder joints remains on the board leaving perfectly exposed and clean pads on the on BGA package (virgin pads) . Note: No mechanical stress wa

BGA Top Cap Detached after reflow Soldering

Electronics Forum | Sat Jun 11 03:26:20 EDT 2016 | nagesh

Hi, I have problem with one of the BGA Top Cap Detached from the Solder Balis attached to the BGA. Advice /Suggest why the Top Cap Has come out. We produced 4150 Pieces & had similar problems with 5 Pieces. Thx in advance for all your suggestions. T

Possibility of a cheaper pick and place machine design?

Electronics Forum | Thu Jul 10 21:11:11 EDT 2014 | andrespena

@Alexei Shkolnik Ah, I hope this doesn't become a problem. But if it does perhaps we can redesign the whole system? Push the components with a pusher that's connected from above rather than pulled by a magnet below. Perhaps the pusher can still clim

Thermocouple

Electronics Forum | Fri Mar 12 11:41:53 EST 2004 | pjc

Don't detach the bead and don't twist the wires! The bead should be what makes contact with where you want to measure temperature. Tape is not the ideal method to attached thermocouples for reflow soldering but is OK when using for wave solder prehea

BGA Detached off the board

Electronics Forum | Mon Aug 11 10:37:19 EDT 2008 | realchunks

I assume you mean the balls of the BGA, not pads (laugh it up guys - I said balls). If so, you may have a no-lead BGA or a high temp BGA.

BGA Detached off the board

Electronics Forum | Mon Aug 11 11:00:40 EDT 2008 | eyalg

RoHS BGA. No lead in it. > RoHS BGA. No lead in it. ok. this is not the case .It was sn/pb type...

BGA Detached off the board

Electronics Forum | Mon Aug 11 13:55:09 EDT 2008 | guhansub1

Your defect may be possibly due to black pads, although it is rare on component side. Is your BGA pad finish ENIG? If so, inspection using a SEM can give clues on the presence of black pads

BGA Detached off the board

Electronics Forum | Mon Aug 11 14:04:51 EDT 2008 | realchunks

Then your profile is way off. You need a t-couple mounted under the BGA on one of the center balls to measure correctly.

  1 2 3 4 5 Next

detached searches for Companies, Equipment, Machines, Suppliers & Information

SMT spare parts - Qinyi Electronics

Reflow Soldering 101 Training Course
Selective soldering solutions with Jade soldering machine

Wave Soldering 101 Training Course
Equipment Auction Automotive Electronics Supplier - Closure of Tier-One SMT Dvision: (10) ASM & Universal SMT Lines & Feeders Equipment as-new-as 2019! Dek | Koh Young | Speedline | Vitronics | Viscom

Best Reflow Oven
Pillarhouse USA for handload Selective Soldering Needs

Training online, at your facility, or at one of our worldwide training centers"
PCB Depanelizers

Low-cost, self-paced, online training on electronics manufacturing fundamentals