Electronics Forum: die attach adhesive (Page 1 of 18)

BGA attach eval.

Electronics Forum | Wed Apr 02 23:02:38 EST 2003 | scottf

I agree with Iman. Verify the integrity of the component for moisture. Most definately place an amount of ownership on your PCB supplier. Request tank analysis results and copies of the lot travelers. Look specifically for any in process rework pro

BGA attach eval.

Electronics Forum | Tue Apr 01 11:50:08 EST 2003 | rdr

Dave, thanks for the info. This sounds like it would verify the presence of an open. We have verified that these balls are open and I am trying to figure out if we are fracturing or not wetting. causing these opens. I would use the die method on ne

Die attach with solder paste

Electronics Forum | Wed Aug 28 10:16:12 EDT 2002 | Jim M.

Sam We install a lot of die in the SMT room using same process as SMT parts.Water soluble solder paste is used for attachment of die to ceramic and boards. Biggest problem i found is the adjustment from installing the die in the bonding area. The t

Die attach with solder paste

Electronics Forum | Tue Aug 27 03:45:36 EDT 2002 | seje

Hi there. We are considering to attach die chip with solder paste to the pcb at the SMD line (we are used to attach it with silver epoxy at the die bonding line before). This is a whole new method to me, so I'd like to have some opinions here. Where

Die attach with solder paste

Electronics Forum | Fri Aug 30 06:18:55 EDT 2002 | seje

Thanks Jim, that should help. And yes, there is light at the end of the tunnel.... now : ) -Sasu-

High-temperature thermal profiling adhesive

Electronics Forum | Fri Jan 09 18:28:34 EST 2004 | Ron W

I'd like to know if anyone could recommend a good high-temperature adhesive that can be used for thermocouple attachment. I've always used high-temp solder and tape in the past, but would like to try using adhesive. Any info is certainly appreciated.

High-temperature thermal profiling adhesive

Electronics Forum | Sat Jan 10 10:37:15 EST 2004 | cyber_wolf

We have always had success with light cure adhesives for probe attachment. Try these guys for some samples. http://www.dymax.com

adhesive for thermocouple

Electronics Forum | Fri Apr 30 08:28:39 EDT 2004 | davef

Roger Saunders, President Saunders Technology, Inc wrote a fairly unbiased paper that compared different thermocouple attach methods. You can probably find it on their site. In it, about gluing thermocouples, he says: There are two general classes

adhesive for thermocouple

Electronics Forum | Fri Apr 30 11:55:55 EDT 2004 | Chris Lampron

Hello Fredrick, I have used several methods of TC attachment including quick set adheasives (not good at reflow temps as Dave suggests) long set two part epoxies (work well if you have the time to wait for a sufficiant cure) temprobes, tape (kapton

Re: Heatsinks for surface mount devices - adhesive alternative!

Electronics Forum | Mon May 24 17:17:21 EDT 1999 | JohnW

| | Can anyone steer me towards a supplier of heatsinks suitable for use on a PQFP 160. Before you shoot me down in flames, I know that I am not going to get much heat away from the die because of the plastic but the application is such that the boar

  1 2 3 4 5 6 7 8 9 10 Next

die attach adhesive searches for Companies, Equipment, Machines, Suppliers & Information

Equipment Auction Automotive Electronics Supplier - Closure of Tier-One SMT Dvision: (10) ASM & Universal SMT Lines & Feeders Equipment as-new-as 2019! Dek | Koh Young | Speedline | Vitronics | Viscom

Best Reflow Oven
Electronic Solutions

Component Placement 101 Training Course
Void Free Reflow Soldering

Software for SMT placement & AOI - Free Download.