Electronics Forum: dynapace 30 inch conveyor (Page 1 of 2)

DynaPace C17727 48 inch Con

Electronics Forum | Fri Dec 10 11:36:44 EST 2010 | reic1

We just recently purchased a Dynapace 48" conveyor with digital display. Am in need of operation and maintenance manuals. Any assistance would be greatly appreciated. Thank you!

Dynapace conveyor

Electronics Forum | Mon Apr 26 16:02:30 EDT 2010 | markhoch

Are the drive motors DC? Reverse polarity on the motors and switch your photosensors on the entry and exit end. You might have to play with the SMEMA connections a bit, but you'll figg it out. ;)

SMT/ PCT edge conveyor replacement belts

Electronics Forum | Thu Dec 13 10:30:42 EST 2007 | slthomas

I would never have guessed that McM-Carr would carry that stuff (antistatic belts) but you learn something new every day....thanks! Question, though. Their online catalog says to order by the inch of circumference (OC, or outer circle), implying tha

SMEMA Conveyor into Reflow Oven? How to handle end of line signal.

Electronics Forum | Wed Dec 30 11:10:53 EST 2015 | ilavu

Tom, Mount one sensor at about 6 inch inside of the beginning of the oven conveyor and use its output as ready to accept the board signal. That 6 inch distance will give you timing and space between two boards entering in the oven. Tushar

MyData TWM

Electronics Forum | Wed Jan 18 09:06:30 EST 2006 | ronhammer

What I mean by it does not work is after I moved the brackets I have about 4.5 inches from the end of the TWM to the conveyor point. None of our conveyers fit there all our Conveyers have about 6 inches in the front on the conveyer. Is there a differ

SMT MACHINES

Electronics Forum | Fri Sep 30 09:03:55 EDT 2005 | davef

Pick and place: * Fuji: The largest pcb size is 20" by 18" for pick and place; 18"x14" for chip shooters. * MYDATA has machines that can be configured to 34" X 44" X 0.500" * Fuji has the NP XL series that will allow 27 by 23 inch boards using a con

Manual handling aftrer Pick n place

Electronics Forum | Sat Jan 22 16:39:26 EST 2011 | eadthem

Your typical high mix line would consist of, Stencil printer, 1-2 foot conveyor belt, fast PNP machine (say a universal 30 spindle turret lightning head), 1-2 foot conveyor belt, large/heavy part PNP (say a universal flex jet 7 spindle or 4 Spindle),

no contact on BGA

Electronics Forum | Fri Jun 29 23:10:02 EDT 2001 | Danial

Thanx for the reply guys!! The problem happened on only one PBGA, the balls are eutectic and the paste volume height is at 5.96 mil min. The stencil opening has been increased to 30 mil which initially was 20 mil. You guys are right!! One probable

BTU Paragon 150 Reflow Oven

Electronics Forum | Mon Apr 24 14:04:44 EDT 2006 | pjc

You did not tell us where your boards fit on the thermal mass range. That is key. I've run Pb Free low to medium thermal mass boards with good results on a 5 zone oven (5 top/5 bottom). You should not have a problem running a medium thermal mass boa

Re: Need Wave Solder Help (SMT)

Electronics Forum | Wed May 26 15:56:08 EDT 1999 | Chrys Shea

| | | we have just started wave soldering passive SMT components and through hole. We are having trouble with voids on the SMT components. It is very random, but effects a lot of TSOT's. We are using an electrovert with a chip wave. Are there any

  1 2 Next

dynapace 30 inch conveyor searches for Companies, Equipment, Machines, Suppliers & Information