Electronics Forum: econopak wave (Page 1 of 6)

wave solder analysis

Electronics Forum | Tue Nov 28 14:02:06 EST 2006 | jsloot

I am starting to use a DATAPAQ wave analysis software on our Econopak EPK II machines. I would like to know what values you may be using for alarm conditions. I can email an example if you can help. Thanks

Nitrogen wave soldering

Electronics Forum | Thu Feb 13 08:28:47 EST 2003 | pjc

Call 1-800-737-8110 for tech support. They can give you the N2 supply specs for the 650C. You should consider the cost to convert the Contour to a standard Lambda vs. the cost to bring in N2 and the consumable costs. Tech Support can give you the ret

Board wave soldering

Electronics Forum | Mon May 19 10:35:58 EDT 2008 | samir

I agree with RealChunks. The application of any of these "wave solder process control tools" is dependant on how the shop is run. At some shops, PM is inconsistent and slacked off on. At other shops, there is no technical expertise at the operator

After market preheaters for Electrovert wave machine(s)

Electronics Forum | Tue May 07 10:32:13 EDT 2002 | Todd M. Troyer

Does any one know where I can get after-market preheaters for an Electrovert Econopak II SMT wave?

Electrovert Ultrapak 600C wave solder machine - HELP!?!?

Electronics Forum | Tue Jan 10 11:34:11 EST 2017 | charliedci

Have you contacted Speedline? They took over the Electrovert products and have provided us with parts and support on our 25 year old Econopak +.

Spray fluxer conversion

Electronics Forum | Thu Nov 16 12:52:04 EST 2017 | charliedci

We installed a SonoFlux ultrasonic spray fluxer, replacing the foam fluxer in our Electrovert Econopak wave in 2014. The cost at that time was 16K, installation included. We ran water based flux through it and as long as we kept it clean, worked well

Electrovert Econopak Wave Solder Pot Temperature too much variability/Swing

Electronics Forum | Tue Jun 25 22:22:22 EDT 2019 | proy

We have an electrovert 16" econopak wave solder machine with two identical pots (exchange between Tin Lead and Lead Free). When the pots are exchanged the same thermocouple is used, and the same controller is used - with the set point adjusted. The S

Electrovert Econopak Wave Solder Pot Temperature too much variability/Swing

Electronics Forum | Wed Jul 10 22:13:45 EDT 2019 | SMTA-Ray

I don't recall if the heater wattage is the same or not for the different pots. If the wattage is different then the PID algorithm is also different. this anticipated when & by how much the heater will overshoot its setpoint and turns the heater off

Titanium Wave Solder Fingers

Electronics Forum | Tue Jan 20 21:37:26 EST 2004 | alwil

I am looking for a supplier or a manufacturer who can help me with Titanium Fingers for our Electrovert Econopak Plus wave solder. I am looking for the "v" groove type and also the 90 degree type fingers. I am in Australia. Thanks.

Rebuilding Electrovert Solder pump motors...

Electronics Forum | Mon Feb 28 11:24:13 EST 2005 | EHess

Still looking for a second source for the Electrovert Econopak II wave solder pump motors, or a place that rebuilds them. anyone? Anyone? Beuhler?

  1 2 3 4 5 6 Next

econopak wave searches for Companies, Equipment, Machines, Suppliers & Information

ISVI High Resolution Fast Speed Industrial Cameras

High Resolution Fast Speed Industrial Cameras.
2023 Eptac IPC Certification Training Schedule

IPC Certification Training from the comfort of your home or office
Assembly Automation Technology

I've got PARTS for FEEDER REPAIR --- Sean at SMTXtra