Electronics Forum: electrician (Page 1 of 2)

Need help for setting up an assembly line

Electronics Forum | Wed Jun 21 16:04:07 EDT 2006 | bman

"Another question, is the facility with 200A @ 208V able to operate this assembly line properly?" That could be a problem, big ovens pull a lot of juice. Our 7 zone Conceptronic HVN-102 runs on 480 Volts and is on a 160 amp breaker, for example. Y

MYDATA TP11 - Motor Controller M error

Electronics Forum | Fri Jun 03 15:19:19 EDT 2011 | jeremymc

After reseating the M controller boards I was able to get further than I had previously, no save status error, and was given an error about the voltage being wrong. During my last run my company had an electrician in to rewire somethings and put a

Heller 1800 exl wiring

Electronics Forum | Wed Jun 14 18:33:39 EDT 2017 | caurbach

1. Why isn't an electrician doing this? 2. Did you measure phase-to-phase voltage between each phase at the machine? 3. Phase rotation only affects the 3-phase motors. If it's out of sequence, the motors will spin backwards but everything else sho

3-Phase Corner-Grounded Delta & GSM

Electronics Forum | Tue Aug 04 14:28:39 EDT 2020 | ttheis

Yes, I am certain it is 240 corner grounded delta. It confuses many electricians and it took me some time to understand. It is fed from a 480:240 delta 200A transformer. As I mentioned, they have a lot of Bridgeport 3ph machines and cnc machines conn

Micropax continued

Electronics Forum | Tue Aug 24 09:13:17 EDT 1999 | Earl Moon

Again, I really appreciate the valuable input you all provided. Got my Air-Vac SRM4 machine Friday afternoon. Stored it safely in my cube over the week-end for safe keeping. Tried to find 220V single phase next to air with no luck yesterday. Electric

Re: Avoiding Blood letting on stencil printer

Electronics Forum | Sat Nov 17 08:05:19 EST 2001 | caldon

TONY- I don't beleive the Craftsman called this posting in. Nurses are not supose to stick themselves with needles, Carpenters are not supose to get splinters, Electricians should never get shocked.....but in reallity it happens. Risk assesment is a

what is the cause of humming/vibration of a ballast x'former

Electronics Forum | Thu Mar 02 13:13:14 EST 2006 | Chunks

A ballast is the device needed to energize fluorescent lamps during operation. In all fluorescent lighting systems, the ballast provides the proper voltage to start the lamp and then regulates the electric current flowing through the lamp to stabiliz

SMT line cable management

Electronics Forum | Tue Feb 07 10:18:34 EST 2017 | swag

Our entire shop floor has a hanging uni-strut grid ceiling approx. 10 feet up. The actual ceiling of the building is probably 16 ft. max ceiling with pitch. We run all air lines and power on it. The uni-strut is hung by all-thread rods. Sounds co

Interference to lights from Heller 1707 XL oven

Electronics Forum | Sat Sep 12 04:19:28 EDT 2020 | SMTA-64387098

I have just built a new factory and installed the old Heller 1707 XL oven. When I run the oven the LED panel lights and downlights in the entire building begin to shimmer after 2nd zone is switched on. It does not get worse when the whole 7 zones are

Re: Micropax continued

Electronics Forum | Tue Aug 24 15:10:25 EDT 1999 | Earl Moon

| Again, I really appreciate the valuable input you all provided. Got my Air-Vac SRM4 machine Friday afternoon. Stored it safely in my cube over the week-end for safe keeping. Tried to find 220V single phase next to air with no luck yesterday. Electr

  1 2 Next

electrician searches for Companies, Equipment, Machines, Suppliers & Information

ISVI High Resolution Fast Speed Industrial Cameras

World's Best Reflow Oven Customizable for Unique Applications
Online Equipment Auction of Altronic: Small-Batch Surface Mount & Assembly Facility

Wave Soldering 101 Training Course
PCB Handling Machine with CE

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
PCB Depanelizers

Private label coffee for your company - your logo & message on each bag!