Electronics Forum | Wed Apr 18 15:10:35 EDT 2012 | smtivan
Dear Colleagues! Our organization has a lot of not-intellectual feeders for Essemtec Pick&Place CSM7000, but we would like to use this feeders in Essemtec CSM7100. Does it possible? What will we need to do for normal work of CSM7100 with old feeders
Electronics Forum | Sat Apr 21 15:03:23 EDT 2012 | lakritzstange
Hi all, we have a Mirtec table top system MV-7. We are trying to use the ocr function to "read" the letters on the IC/resistors and so on. But the results are really bad. From other company using other machine i know that ocr is working fine. Ha
Electronics Forum | Fri Apr 27 08:19:04 EDT 2012 | jim_n_hky
Can anyone offer guidelines on DFM and process recommendations for soldering .050" pitch connectors in the wave. The initail design had .026" drill with .043" pads so only .007" between pads. I requested .035" pads, but this still only leaves .015" b
Electronics Forum | Wed May 02 11:27:17 EDT 2012 | aj
Are you having problems with alignment of BGA's or perceiving that you will have problems. We run thousands and they re-align very well with leadfree if slightly off - Do you handplace all your BGA's? I would imagine there would be cosiderable cos
Electronics Forum | Wed May 02 04:25:50 EDT 2012 | geb
Hi, We power down our reflow oven over the weekend, but before that we let the heating zones cool to approx 100degC. Its something we've always done as we were told to do it when we bought the line. Does anyone else do this, and what would happen if
Electronics Forum | Fri May 04 11:47:56 EDT 2012 | pctech
Hi, It's not advised to hard-down the re-flow oven.There are two reasons for that ; extreme thermall difference in temp. will cause chain and drive shafts to warp and T/C's to crack.Let your "cooldown" profile do this safely within 45 mins. to an hou
Electronics Forum | Thu May 03 15:07:59 EDT 2012 | rodrigo
Hi all, What the largest part I can place with these machines? I'm going to try to install a PLCC68 using the front light because the part is bigger than the backdisk and I want to make sure it can handle it. The part is about 30mmx30mm. Thanks
Electronics Forum | Sat Aug 03 04:33:18 EDT 2013 | sarason
There is one Essemtec CML7000 om ebay right now http://www.ebay.com/itm/Essemtec-Pick-and-Place-Machine-CML7000-CML-7000-/321164969584?pt=LH_DefaultDomain_0&hash=item4ac6ec8670 regards sarason
Electronics Forum | Fri May 04 12:08:04 EDT 2012 | gnus
Hi. I got an old MPM SPM printer and recently the hard drive crashed and couldn't be saved. We sourced a hard drive but the problem is we don't have the actual software and cannot retrieve it from the dead hard drive. Does anyone have it or can point
Electronics Forum | Mon May 07 21:08:19 EDT 2012 | abyan
Hi..I need help again.. I need negative 18 volt linier voltage regulation, but after I search for a while, all of the components with this spec is obsolete, an the only exixting component is the through hole one.. Can you show me where I could find a
Manufacturer of PCB depaneling and PCB soldering machines since 2005, products include CE approval V-groove PCB depanelizer, PCB router, PCB punching machine, laser depaneling, hot bar soldering machines and soldering robots.
Liwu Industrial Park, Yuanzhou Town, Boluo
Huizhou, China
Phone: +86-138-29839112