Electronics Forum | Fri Nov 18 15:06:44 EST 2011 | jeffharley
Have you checked each heater rod with a fluke temp. meter or similar to make sure that the elements are in fact heating up? Make sure you have voltage to all heater rods. Check to see what the plc controller is set at. Hope this helps.
Electronics Forum | Thu Dec 01 13:24:45 EST 2011 | kmakiya
Sounds like you have a bad heater. Check current on each leg of the heater circuit, CON6 for the wash and CON7 for the rinse. The current should be the same on each leg. Trek is now part of Stoelting, tech support is 920-894-2293. Hope this helps if
Electronics Forum | Fri Nov 18 18:09:01 EST 2011 | ssupertuba
I have a DEC 265 GS screen printer that won't come up. I know it's old, but it just died in the middle of a run. None of the Euroamps have a display now and the computer just won't see them. Does anyone have an idea of where to start looking?
Electronics Forum | Sat Nov 19 18:35:39 EST 2011 | johndoe0222
We have an old Fuji GSP III-4000 we just changed the fiber sensor on the in-bound and outbound of the printer. The problem we are having now is the board would only go midway the table and it would go up. It does not even reach the main stopper and t
Electronics Forum | Tue Nov 29 14:55:17 EST 2011 | jlawson
N2 is a reflow process widener so to speak, for leaded reflow less of a impact, for LF more impact, and if using finer LF solder pastes T4,T5 and smaller paste deposits generally, it helps widen window for flux in paste in oxide protection during soa
Electronics Forum | Tue Nov 22 17:08:03 EST 2011 | mikenagle
I am looking for process suggestions. We want to use a pin transfer system to deposit adhesive to hold bottom side SMD's in place. We will place SMD's and through hole power parts on the top side and then run through a wave solder machine. Are ther
Electronics Forum | Wed Nov 23 16:53:09 EST 2011 | davef
There's a lot of excellent dispenser suppliers out there that will willingly claw their competitors' eyes out to get your business. Note: Camalot Essemtec Asymtek (Nordson) Precision Valve Creative Automation GPD IJ Fisnar Janome Fuji NE3000S fuji
Electronics Forum | Fri Dec 02 16:26:00 EST 2011 | davef
Here's some recommendations from various companies: * http://www.sibex.com/pcbguidelines.pdf * http://www.carltonindustriesonline.com/Docs/Fiducial.doc * http://www.tracktronics.com.au/pdf/PicknPlace_Fiducials.pdf * http://microtronix.co.za/pcb_re
Electronics Forum | Fri Nov 25 04:10:21 EST 2011 | bwjm
Hi, I am facing some problems on my soldering joint. My operators perform the solder and left the assembled PCBs on the WIP rack. After 1 week (Due to shortage of components),the solder joint of the components darken. Is it caused by oxidation? If ye
Electronics Forum | Fri Nov 25 09:27:09 EST 2011 | fjtxra
Dear All, I´m looking for a low temp solder paste with Lead. I know that, with lead free, is common solder paste with bismuth for low temp in Pin in Paste line, but one customer aks me about low temp solder paste with lead. If anybody knows about and
Nordson Electronics Solutions makes reliable electronics an everyday reality. Our ASYMTEK, MARCH, and SELECT brands deliver precision fluid dispensing, conformal coating, plasma treatment and selective soldering equipment.
2747 Loker Ave West
Carlsbad, USA
Phone: 18002796835