Electronics Forum | Mon Jan 06 16:58:45 EST 2020 | cbeneat
I would recommend quik-tool. Jim Bernhard essentally the inventor of Grid lok left when they went to DEK. Started quik-tool, we use grid-lok in our printers, quik-tool in our Panasonic P&P instead of support pins. Like quik-tool alot more. JBernhard@
Electronics Forum | Mon Jan 06 11:41:52 EST 2020 | robl
JDT http://www.DEKHEAD.com if you are in the USA Adamtech http://www.adamtech.co.uk/contact.asp if you are in Europe There are some good Chinese suppliers, but a lot of Far East cards can be tarnished & with a reduced life due to running in a high h
Electronics Forum | Mon Jan 06 16:19:32 EST 2020 | richardcargill
haven't tried the MINT as it won't let me get that far !! Swapping the Eproms with card 1 and changing the identifier will let it get to the 'Press SYSTEM key' part of the startup though, then it fails on card 1 instead of 0 so I'll give that a try i
Electronics Forum | Mon Jan 06 09:49:36 EST 2020 | andrewpayonk
Hello, I recently purchased a Hotflow 3 oven, using a step up transformer I received with unit, 220v to 480v. Unit turns on but does not heat up. Getting an F02 error saying no convection. I am getting 480v to oven, I also switched the phase still
Electronics Forum | Wed Jan 08 19:16:56 EST 2020 | spoiltforchoice
http://suddendocs.samtec.com/literature/em_tectalk8a_lr.pdf Even so its still a fairly manual process so I guess you really have to want to use this type of connector because its a whole process in itself and I bet the whole family is a special or
Electronics Forum | Thu Jan 09 17:28:07 EST 2020 | dwl
2-3 weeks? wow! I've had stencils last over a decade and only needed replacing because the adhesive holding the mesh dry rotted and crumbled. Of course build volumes were in the order of 50-100 per year. Just goes to show there is no easy answer f
Electronics Forum | Thu Jan 09 18:26:21 EST 2020 | spoiltforchoice
Much like DWL we have multiple stencils that are really quite old (~2003 and still in use) and are perfectly OK. In fact I don't think we've ever worn one out, higher volume designs are far more likely to get a layout change before the stencil gets
Electronics Forum | Fri Jan 10 13:21:34 EST 2020 | emeto
Yes, think of 3prints/minute 24 hours. This is about 4000 prints a day. than you have a marginal process, because customer locked design and doesn't want to change anything. So in our case for 70k-100k prints and we had to change them as the perform
Electronics Forum | Thu Jan 09 08:40:37 EST 2020 | raeesrajput
Hi Every one, Thanks in advance for your help and support. I am getting errors 'Nozzle pick up error' and 'Nozzle release error' on Mirae Mx350. I have been told to calibrate Nozzle Holes using 'ANC' option in the Menu. Ther
Electronics Forum | Fri Jan 10 03:40:41 EST 2020 | jakapratama
Hi, Some nano coat supplier said that you can drop water to the surface where the coating supposed to present before to check. If it's beading, it's still there. I take it that you meant by self in-house wiping of coating, yes? Stencil supplier nan
Nordson Electronics Solutions makes reliable electronics an everyday reality. Our ASYMTEK, MARCH, and SELECT brands deliver precision fluid dispensing, conformal coating, plasma treatment and selective soldering equipment.
2747 Loker Ave West
Carlsbad, USA
Phone: 18002796835