Electronics Forum: electrovert and cfg (Page 1 of 2)

0402's and Gluing.............

Electronics Forum | Wed Feb 09 11:37:26 EST 2005 | pjc

Technical support cannot help with this issue, especially Electrovert tech support, those guys only know soldering and cleaning machines. Contact Jim Kaler at Camalot Applications Support: 603-641-8666 ex7208 or jkaler@speedlinetech.com Tech support

Wave flux and profiling

Electronics Forum | Sat Dec 16 08:23:11 EST 2006 | pr

The "Wave optimizer" is a little pricey but is easy to use, gives instant feedback (display on the unit as opposed to hooking it up to a computer)and will give feedback on the waves, as well as preheat. They will send you a unit to trial for a week o

GSM2 Universal user name and password

Electronics Forum | Tue Oct 09 16:01:48 EDT 2012 | dilogic

Try this - boot machine to OS/2 and interrupt USOS startup procedure, go to USOS/CONFIG folder and rename PSWDUSER.CFG to something else, in case you will need it. Then copy the attached file and reboot.

0402's and Gluing.............

Electronics Forum | Tue Feb 08 23:29:54 EST 2005 | mrduckmann2000

Help! Does anyone know how to get a Camolot Gem II machine to put down dots for 0402 placement? I have been working with Electrovert Tech's that say their machine WILL place dots for 0402's. I have reduce the speed of the pumps to half the speed,

Vectra password

Electronics Forum | Tue Jan 17 17:28:47 EST 2006 | mrduckmann2000

Adlsmt, We had an issue where an Engineer setuo his own passwords on our machine, he was then laided off and nobody knew the passwords. Electrovert gave us the following passwords to try: Electrovert Wave Solder Logon Id Supervisor Password Pass

Printer and Reflow Oven Recommendations

Electronics Forum | Fri May 15 14:50:40 EDT 2015 | emeto

My top 3 printers: 1.DEK 2.MPM 3.EKRA Top 3 ovens: 1. BTU 2. Vitronics 3. Heller or Electrovert

Wave Cassettes and Heat convection

Electronics Forum | Mon Jan 15 13:12:18 EST 2007 | realchunks

So others can solder the same board and part but you can't. Dipping the legs in flux doesn't help. Then it's either your pre-heat or wave. Measure your pre-heat and compare to others or flux mfger. Do you have chip wave or something like an Omega

Printer and Reflow Oven Recommendations

Electronics Forum | Fri May 22 17:48:48 EDT 2015 | aemery

It's your first line, go with established manufacturers. Whether new or used it ultimately comes down to does the tool do the job and how well is it supported (labor/parts) if it does break down. I am a former field eng. with Speedline and now run

Indium No-clean and Inert Reflow oven (N2)

Electronics Forum | Thu Aug 01 13:04:57 EDT 2002 | gdstanton

Its interesting. It appears I'm getting conflicting feeback from Indium. This says its not a problem... http://indium.custhelp.com/cgi-bin/indium.cfg/php/enduser/std_adp.php?p_sid=kTDKGClg&p_lva=&p_faqid=355&p_created=1014734692&p_sp=cF9ncmlkc29

Wave Soldering and Through Hole Forums

Electronics Forum | Thu Jan 24 19:58:58 EST 2002 | davef

for regular eutecticish solders, keep the pot temperature between 230�C [446�F] and 290�C [554�F]. If you polled us on our pot temperatures, we�d be all over the map, but with more lower than higher than you. High pot temperatures tend to generate

  1 2 Next

electrovert and cfg searches for Companies, Equipment, Machines, Suppliers & Information