Electronics Forum: electrovert omniflo-7 (Page 1 of 2)

Electrovert Omniflo 7

Electronics Forum | Thu Aug 20 11:38:57 EDT 2020 | stephendo

You might have to adjust both ends to match the middle. Is it an autowidth oven?

Omniflo 7e schematics + Manuals

Electronics Forum | Wed Jan 19 14:43:51 EST 2011 | davidalvarez

Im looking for manuals + schematics and repair information for an electrovert omniflo 7e reflow oven manufactured in 1999, also intrested in the Bill Of Materials if available. Any information on where these can be obtained and where replacement part

Electrovert Omniflo-7 Reflow Oven VS Lead-Free

Electronics Forum | Thu Feb 10 09:25:44 EST 2005 | lyrtech

Hi, Actually we're looking for a new reflow oven regarding lead-free process and higher capacity production. We have an opportunity for a second hand Electrovert Omniflo-7 (nitrous ready) that respect our budget. My questions are: Does anyone ha

Electrovert Omniflo 7

Electronics Forum | Wed Aug 19 13:52:11 EDT 2020 | goldendragon

Hello guys, Please help me how to parallel the width chain, it is bow out in the middle and keep dropped the board in oven, I can't find anything there that I can manually adjust the middle width to the same size with the entrance and exit. HELP!!! T

Electrovert Omniflo 7

Electronics Forum | Thu Aug 20 14:46:26 EDT 2020 | goldendragon

Yes, it's autowidth oven. I thought about manually adjust both end to match with the with the middle. Thank you very much! Tim

Electrovert Omniflo 7

Electronics Forum | Thu Aug 20 16:28:11 EDT 2020 | cyber_wolf

My guess is that someone either clamped a board or a ramp at the end while adjusting the width. I have had this issue before. Remove the rails and look down them like a gun sight. I have never had any luck trying to adjust out big bends. If you wan

Electrovert Omniflo 7 reflow ovens

Electronics Forum | Thu Aug 30 13:22:47 EDT 2001 | arzu

180deg More important are the preheat and soakzones and temp ramps. How to check: I used to do it as follows: use a TEST-PCB with fixed thermocouples and connect it to the mole. Print the profile on transparant paper. do it again e.g. each week and

Electrovert Omniflo-7 Reflow Oven VS Lead-Free

Electronics Forum | Thu Feb 10 16:45:36 EST 2005 | pjc

It all depends on what type of board you need to solder. If your boards are small in size and low thermal mass and your conveyor speed requirments are normal, then I'd say the OmniFlo 7 will do the job. It has a max zone temp setting of 280C. The cur

Soldering oven

Electronics Forum | Mon Jan 19 08:37:16 EST 2009 | lkpdsund

Hello all! We possess a speedline electrovert omniflo 7 reflow oven at my site. Last week we examined how the solder profile was affected by fan-speed and by providing the soldering process with compressed air(O2) or nitrogen(N2). We also ran the sa

Electrovert Omniflo 7 reflow ovens

Electronics Forum | Thu Aug 30 11:59:00 EDT 2001 | Spanky

Hey all, I have 3 questions about reflow. Hopefully someone can help me. 1. I am having a problem. I set the peak at 230 and my mole thermocouples are telling me the temp in that zone gets to 237. How is this possible even if the thermocouple

  1 2 Next

electrovert omniflo-7 searches for Companies, Equipment, Machines, Suppliers & Information

ZESTRON Surface Insulation Resistance

Best Reflow Oven
Fourier Transform Infrared Spectroscopy

World's Best Reflow Oven Customizable for Unique Applications
SMT feeders

PCB Assembly Supplies - ONLINE STORE