Electronics Forum: ersa and 2/14 (Page 1 of 1)

BGA rework and inspection

Electronics Forum | Thu May 30 10:31:03 EDT 2002 | robbied

Hi Yannick. This is an issue that we are just recently getting into but here is some ifo that I have gathered so far. I have seen/ used 2 different rework machines. The one we have bought is a 'PACE TF2000' which was at the lower cost end of the mar

BGA ball and PCB pad

Electronics Forum | Wed Feb 18 12:42:43 EST 2004 | babe

OK, if the sphere of the ball and the paste on the pad are both eutectic, 63/37 then the paste will reflow first causing a drop of the component, after which the spheres will reflow causing a double drop and a good intermettalic. You can see this by

Rework and repair system suggestions

Electronics Forum | Thu Jan 27 11:33:59 EST 2005 | russ

For what you have right now I would recommend that you use soldering iron tips that are made for component removal. until you get BGAs I wouldn't worry a whole lot about the expensive rework equipment. I would use specialty tips and a heat gun wit

SMT and BGA Rework Machine

Electronics Forum | Tue Aug 22 03:04:07 EDT 2006 | PP

Any help/suggestion is much appreciated I am doing lots of BGA Reworks from a small uBGA with a few balls to a large BGA with over 1500 balls. The reworks have been done on SRT 1100 Series Machine for many years. SRT 1100 Machine is good for the c

Rework and repair system suggestions

Electronics Forum | Thu Jan 27 06:39:59 EST 2005 | reash

For now, on this first board, we will be reworking components such as 0805 and 1210 size caps and resistors, along with SOT-23 and SC-70 size packages. We might eventually get into BGAs. This board will most likely be a double-sided board, probably

Printer and Reflow Oven Recommendations

Electronics Forum | Fri May 15 21:39:48 EDT 2015 | jlawson

Reflow.. 1.Rehm (Germany) - Best in Class Best overall process stability heating system ( Alot of makers have started to copy there VX heating arrangement ). COnveyor chains can be a bit more attention in terms of maintenance on rehm , but if foll

Vacuum for Wave and Selective Solder Maintenance

Electronics Forum | Sat Mar 11 08:53:44 EST 2017 | tch

My company is looking for a vacuum that can handle being used to clean up solder splashes on the bottom of our wave solder machines and around the solder pot area in our ERSA Selective Solder Machines. In the past we would use a Shopvac but these don

Your opinion about RoHS and WEEE ?

Electronics Forum | Fri Dec 24 05:12:08 EST 2004 | Patrick Tavernier

Hi ! Thank's for your replies. I'm seeing you're very concerned about this subject. I think RoHS and WEEE arrive too soon. Not technological solution about whiskers and tin pest. RoHS implicates a lot of money for to implemente news process. We must

Advice on used pick and place machine

Electronics Forum | Mon Oct 09 13:36:30 EDT 2006 | ppminc

Phil, The QSA-30 was built by Sam Sung, Sold by Quad. Single Head 2 Nozzles around 11K CPH Quad does not support the machine but I believe you can get parts direct from Sam Sung. I am not sure if they have a registration fee. The QSA used Quad made

Reflow oven bottom heaters

Electronics Forum | Thu Nov 16 08:57:00 EST 2017 | jandon

We found used Ersa HotFlow 2/14 reflow oven that does not have bottom side preheaters. Can it be easily and safely used in normal high mix/low volume production or is it built for specific products which does not need bottom preheaters?

  1  

ersa and 2/14 searches for Companies, Equipment, Machines, Suppliers & Information