Electronics Forum: ersa and convection (Page 1 of 7)

wave profiling for ersa ews500

Electronics Forum | Fri Jan 13 12:12:48 EST 2006 | jimk

we have 4 bottom IR heaters and a 2 zone bottom Quartz heater (2 lamps/4 lamps) and 1 convection heater above zone 1 IR. we have very tight restrictions from customer and I could send profile view to your email if possible

Wave Cassettes and Heat convection

Electronics Forum | Tue Jan 16 07:11:24 EST 2007 | tk380514

I cant touch the pre-heat as it would affect all other products or so i am told by the Qaulity manager. Maybe they think i am Mickey Mouse and the pcb�s jump around the factory like a scene from Fantasia :) if this was only the truth.

Wave Cassettes and Heat convection

Electronics Forum | Tue Jan 16 07:07:17 EST 2007 | tk380514

Answers: The component does take solder, no problem We get a full barrel fill with an empty PCB but only on one of the holes, the other hole has so much copper around it. The flux reached the top of the PCB when I tested the empty PCB. The IPC-A-610

Wave Cassettes and Heat convection

Electronics Forum | Tue Jan 16 07:51:19 EST 2007 | realchunks

Your Quality Manager won't let you make changes, yet you get blammed for process problems? First, you need a change in management. Second, if you can't change set pre-heat temps, change the conveyor speed. Slow it down and see if your joints loo

Wave Cassettes and Heat convection

Electronics Forum | Mon Jan 15 11:41:56 EST 2007 | davef

Questions are: * Does the component take solder when you dip it in the solder pot to test the solderability of the leads? * Can you get full barrel fill when wave soldering a bare board? * Is your flux reaching the top of the board through the hole b

Wave Cassettes and Heat convection

Electronics Forum | Mon Jan 15 13:12:18 EST 2007 | realchunks

So others can solder the same board and part but you can't. Dipping the legs in flux doesn't help. Then it's either your pre-heat or wave. Measure your pre-heat and compare to others or flux mfger. Do you have chip wave or something like an Omega

Wave Cassettes and Heat convection

Electronics Forum | Tue Jan 16 07:59:36 EST 2007 | tk380514

we worked out that the wave soldering cassettes Duratstone material takes alomst 35 degree away from the surface of the pcb, and the speed is already too slow it should be over 1.0 - 1.8 meters a minute but its now already 82 cm a minute, in order to

Wave Cassettes and Heat convection

Electronics Forum | Mon Jan 15 09:19:29 EST 2007 | tk380514

We use Alpha EF-2202 low-VOC No-Clean flux Selective wave soldering cassettes Bottom pre-heating wave soldering machine We have one component that will not solder properly: http://www.epcos.com/web/generator/Web/Sections/ProductCatalog/Capacitors/Ul

BGAs and vapor phase

Electronics Forum | Fri Jul 16 15:30:22 EDT 1999 | SMTASSY

Perhaps a little hard to find but is there anyone who uses a vapor phase process to solder populated card with BGAs. I am interested in the success rate of such a process. It is obvious that the throughput is reduce vs a convection oven but still thi

black and grey pad

Electronics Forum | Sat Oct 06 05:33:47 EDT 2001 | spchua

I had recently encounter the "black and grey" pads problems for the BGA pad after the convection re-flow. The pads shows in in "black and grey" color and a litter solder in it, and it happen in ramdom, when applied heat and solder on the "black and g

  1 2 3 4 5 6 7 Next

ersa and convection searches for Companies, Equipment, Machines, Suppliers & Information

Best SMT Reflow Oven

World's Best Reflow Oven Customizable for Unique Applications
Selective Soldering Nozzles

Training online, at your facility, or at one of our worldwide training centers"
2024 Eptac IPC Certification Training Schedule

High Throughput Reflow Oven
Electronics Equipment Consignment

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
IPC Training & Certification - Blackfox

Have you found a solution to REDUCE DISPENSE REWORK? Your answer is here.
Hot selling SMT spare parts and professional SMT machine solutions

BEST IPC Certifications and Solder Training Online!