Electronics Forum: ersa and nozzle (Page 1 of 19)

ERSA users 1.8/2.5 nozzle

Electronics Forum | Thu Nov 14 18:51:08 EST 2013 | tombstonesmt

We use a 2mm with our Pillarhouse Jade Mark II. We found that reducing the nitrogen enough that the area around the nozzle stays hot enough not to "freeze".

ERSA users 1.8/2.5 nozzle

Electronics Forum | Fri Nov 15 10:54:38 EST 2013 | jaimebc

Thanks for the pointer tombstonesmt, I'll give that a shot. Being able to utilize this nozzle will help tremendously. I'll post results as they become available.

ERSA users 1.8/2.5 nozzle

Electronics Forum | Thu Nov 14 10:24:53 EST 2013 | jaimebc

Recently, we have been experimenting with the 1.8/2.5 nozzle to be able to solder leads that are near an SMD. This pcbs were not design for selective solder, so we are trying to work within this limitations. I found the 1.8 nozzle very hard to insta

Max and Min nozzle settings on CP7

Electronics Forum | Sat Jul 24 04:02:18 EDT 2004 | kent_peterson

Two ways at it.You could just put the same nozzle for both the min and max.Or you could move the feeder into a location that has similar parts using the nozzle you want. With the feeder setup it should be optimized for the least amount of nozzle ch

Max and Min nozzle settings on CP7

Electronics Forum | Sat Jul 24 04:02:21 EDT 2004 | kent_peterson

Two ways at it.You could just put the same nozzle for both the min and max.Or you could move the feeder into a location that has similar parts using the nozzle you want. With the feeder setup it should be optimized for the least amount of nozzle ch

Max and Min nozzle settings on CP7

Electronics Forum | Mon Aug 02 13:06:10 EDT 2004 | jbabson1

If the CP7 is like the CP643, it defaults to the MAX size unless that nozzle is skipped. Then it would switch to the next smaller nozzle on that head.

Max and Min nozzle settings on CP7

Electronics Forum | Tue Jul 20 04:16:02 EDT 2004 | Charles Huang

Wondering if there any CP7/F4G programmers out there that can help me out with this one. I'm assuming the setting for max and min nozzle in the "environment" section of the part data would allow me to use either the specified max OR min nozzle in th

Pick and Place Rivet

Electronics Forum | Wed Aug 13 17:39:27 EDT 2008 | awegener

In light of this new information I've received from everybody's comments, I'd like to get more information about pick and place nozzles. How can I learn more? ... What do the nozzles look like? Are there different shapes? What kind might you r

Pick and Place Nozzles

Electronics Forum | Mon Aug 18 15:03:38 EDT 2008 | awegener

I'd like to get more information about pick and place nozzles. How can I learn more? ... What do the nozzles look like? Are there different shapes? Are custom nozzles sometimes used for custom parts or are the nozzles mostly standardized? What kind

Pick and Place Nozzles

Electronics Forum | Mon Aug 18 22:55:05 EDT 2008 | kpm135

Nozzles are really machine specific. Your best bet, if you're looking for the correct nozzle for a part, would probably be to send a strip of parts and the data sheet to the manufacture of the machine and ask them for their recommendation. Most machi

  1 2 3 4 5 6 7 8 9 10 Next

ersa and nozzle searches for Companies, Equipment, Machines, Suppliers & Information

Online IPC Training & Certification

World's Best Reflow Oven Customizable for Unique Applications
Reflow Ovens

MSD Dry Cabinets


SMT PARTS