Electronics Forum: ersa nitrogen (Page 1 of 2)

Time to retire the wave?

Electronics Forum | Tue May 22 10:44:04 EDT 2007 | stepheniii

Are you using nitrogen with your wave? You probably will need to with selective. With our Ersa we need 99.9% pure nitrogen to make it acceptable. They spec 99.999% which means liquid nitrogen. We tried one board without nitrogen, it left a two in

Nitrogen gassing ring

Electronics Forum | Wed Feb 08 22:05:54 EST 2017 | cromaclear

Hello to all, I am using ersa versaflow 3 selective soldering machine, i am having problems with nitrogen gas ring contamination. How can i clean this rings,what do you use? Ultrasonic bath maybe?

Nitrogen purity requirments

Electronics Forum | Thu Jun 29 10:45:46 EDT 2006 | stepheniii

We have an ERSA Versaflow Ecoselect selective wave soldering machine. It works well except it needs nitrogen. You can't even move the table around if your nitrogen tank is empty. The spec sheet says Required degree of purity: Nitrogen liquid 5.0

Wave replacement : Ersa, Seho, Electrovert or other

Electronics Forum | Wed Jul 25 10:27:51 EDT 2018 | mefloump

We have an Ersa Powerflow N2. It's a very well built machine with excellent support. We run it (2) 10 hr shifts per day, 4 days a week. Having the full nitrogen tunnel has greatly reduced dross and improved hole fill. This replaced an Electrovert Vec

ERSA Selective Solder questions

Electronics Forum | Thu Apr 25 09:57:31 EDT 2013 | jaimebc

We aquired an ERSA ECOSELECT 2 selective soldering machine. So we are going through a learning curve and I would like to hear from ERSA users on this subject. The main concern is to keep the miniwave steady, it seems that it " bounces" a lot and is

ERSA users 1.8/2.5 nozzle

Electronics Forum | Thu Nov 14 18:51:08 EST 2013 | tombstonesmt

We use a 2mm with our Pillarhouse Jade Mark II. We found that reducing the nitrogen enough that the area around the nozzle stays hot enough not to "freeze".

Which one is better Soltec Delta-X or Ersa Powerflow N2 wave solder machine?

Electronics Forum | Mon Jun 29 07:17:25 EDT 2015 | donlockard

Seho maxi wave 3240 should be considered as well. Invented full tunnel nitrogen systems that have lower operating costs and provide yields unlike what can be achieved by air wave systems.

Nitrogen gassing ring

Electronics Forum | Mon Feb 13 06:53:39 EST 2017 | duoman

I would email Chad at ERSA and see what he might have to say, relating to your Versaflow. he's always been a big help to me.

SMT LINE CHOICE

Electronics Forum | Mon May 14 21:27:06 EDT 2018 | jimpat

Congrats. Can you share the rough cost for the 8 zone Heller? Is it nitrogen capable? I am also looking to upgrade and doing preliminary research into BUT, Vitronics, Ersa and Heller.

Time to retire the wave?

Electronics Forum | Thu May 24 14:03:09 EDT 2007 | grantp

Hi, I am ok either way, and the main reason I originally went with Soltec was the overall oven design seemed cleaner than ERSA. The soltec had good performance, but the oven design was neat internally, where the ERSA seemed to be a bit of a mess.

  1 2 Next

ersa nitrogen searches for Companies, Equipment, Machines, Suppliers & Information

Best SMT Reflow Oven

World's Best Reflow Oven Customizable for Unique Applications
Benchtop Fluid Dispenser

Benchtop Fluid Dispenser
Used PCB Assembly Equipment & SMT Equipment

High Resolution Fast Speed Industrial Cameras.
zestron pcb cleaning webinars

PCB Assembly Supplies - ONLINE STORE
smt assembly equipment manufacturer

ARE HUMIDITY INDICATORS PART OF YOUR SUPPLY NETWORK? Register for the webinar!